Rockford Fosgate 250, 360, 400, 500, 600, 800, 1000 manual Power 400 Power

Page 23

I

+ - NS

T

A

L

L

A

T

I

O

N

2-Channel Mode					Power 400 Power 800
						4 -channel			4 -channel
			R C A I n p u t
	4-2
Input
		210 Hz 50				210 Hz	50
		190	55	R	R	190
Front	4/2	145	55	R	R	145	55	Rear
Front	4/2	110	65			110	65	Rear
Crossover	Input	110	65			110	65	Crossover
Crossover	Input	Front	80			80	Rear	Crossover	Rear
HP-Full-LP		Front	Front			Rear	Rear	HP-Full-LP	Rear
HP-Full-LP		Gain	Front			Rear	Gain	HP-Full-LP	Remote
		Crossover		L	L	Crossover			Punch
		Frequency				Frequency			Punch
		Frequency				Frequency			Bass
									Bass
			Front	Pass-Thru		Rear

			REM			LED
LR+	LR-	RR+	RR-	B+	GND	LF-	LF+	RF-	RF+

+ -

4Ω min.

Bridged

Left

-

+

4Ω min.

Bridged

Right

•RCA Inputs are connected to front inputs

•4-2 Input Switch is set to 2-channel input mode

•Gain for front and rear channels must be set identical

•Speaker Impedance for each bridged channel should be no less than 4Ω

•Variable Crossovers for front and rear channels must be set to identical frequency (i.e. both set to 60Hz) and operating mode (i.e. both set to LP)

– 17 –

Image 23

Contents

Power Amplifier + a T Practice Safe Sound Specifications Channel Table of Contents Introduction Power Amplifier Accessory PackPower Amplifier Feature Chart Design Features Power LR+ RR+ RR- REM GND LED LF LF+ RF+ REM REM LR+ LR RR+ RR GND LF- LF+ RF- RF+ 45 cm Black Grounding Wire Wire crimpers Installation ConsiderationsTrunk Mounting Mounting LocationWiring the System Battery and ChargingPage Using Passive Crossovers Speaker Impedance Table of Crossover Component ValuesBridged/Mono Mode InstallationPower Connections + NS Channel ModePower 400 4-channel Power 800 4-channel Power 400 Power H a n n e l P u t Channel4-channel H a n n e l P u t Power REM +GND Power 1000 2-channelChannel ModePower Crossover Operation OperationPass-Thru All ModelsPhase Warp Watt 3-Way System System DiagramsWatt 4-Way System Power Channel AmplifierPower Channel Amplifier Punch Punch Woofers Procedure 3 Check Amplifier if you experience Turn-on Pop Installation TroubleshootingProcedure 1 Check Amplifier for proper connections Procedure 2 Check Amplifier for audio outputInstallation Troubleshooting About the Dynamic Power Measurements Dynamic Power MeasurementsInformation Cubed What is an Amplifier?Length of Warranty Limited Warranty InformationInstalacion IntroduccionMontaje en el Malatero Montaje en el Compartimento de PasajerosTerminal REM Terminal GNDFuncionamiento Estereo Montage dans lhabitacle InstallationMontage Montage dans le coffreOpération stéréo/mono Opération stéréo Einbauort EinleitungREM Anschlub GND AnschlubStereo Operation Dove Posizionarlo IntroduzioneTerminale REM Consenso di accensione Terminale GND cavo negativoStereo Operation Page Page Page Made in the USA