Zebra Technologies R402 manual Media Specifications

Page 62

Media Specifications

Width	1 to 4.25 inches / 25.4 to 108 millimeters)
	1 to 2.25 inches / 25.4 to 57 millimeters (tag stock)

Length	0.5 to 22 inches / 13 to 559 millimeters with standard memory

Gap	0.08 to 0.16 inch (2.0 to 4.0 millimeters)
	0.118 inch / 3.0 millimeters recommended

Thickness	0.003 to 0.007 inch / 0.08 to 0.18 millimeter

Roll Size	Maximum outer diameter: 5 inches (127 millimeters
	Inner Core diameters: 1 or 1.5 inches (25.4 or 38 millimeters)
	Optional media hangers available for larger inner core
	diameters

Requirements	✔ User Zebra-brand direct thermal or thermal transfer media
	that is outside wound. Media may be reflective (black mark)
	sensing or transmissive sensing, die-cut, notched, or
	continuous)
	✔ For die-cut labels, use only full auto dies.
	✔ Notched media must have a 0.5 inch (13 mm) wide by 0.094
	inch (2.5 mm) long cutout located in the center of the roll.
	✔ The reflective media black marks must be located in the
	center of the roll. Mark width 0.5 inch (13 mm) centered and
	perpendicular to the edge of the media; mark length 0.094
	inch (2.4 mm) parallel to the bottom edge of the media.

Transponder	✔ Phillips I•Code
Requirements	✔ Texas Instruments Tag-It™
	✔ Inside Technologies PicoTag®
	✔ ISO-15693

Always thoroughly test your desired media for your specific application before buying in large quantities.

Ribbon Specifications

	Roll Size	Maximum outer diameter: 1.3 inches / 33 millimeters

	Length	2,900 inches / 74 meter capacity; provides 1:1 media roll to
		ribbon ratios

	Width	At least as wide as media

	Setup	Ink-side out

	Requirements	User Zebra-brand ribbon that is outside wound.

Image 62

Contents R402 Users GuidePage Proprietary Statement Page Contents Operation & Options Appendix 980389-001 Rev. a Introduction HelloWhat’s in the Box? Inspecting the Printer Opening the printerInspecting the Printer Closing the printer Reporting Damage Getting Started Modes of PrintingAttaching Power Supply Loading Roll Media Placing the Roll in the Media CompartmentAdjusting the Guides Using the Optional Media Adapter Plates Loading Ribbon Install the Ribbon Supply RollInstall the Take-Up Core Attach and Tighten the Ribbon Auto Calibration Feed Button Power SwitchOperator Controls Status LightPrinting a Test Label Interface Cable Requirements Hooking Up the Printer and ComputerParallel Interface Requirements Adjusting the Print Speed Adjusting the Print WidthAdjusting the Print Darkness Communicating with the PrinterOperation & Options Thermal PrintingReplacing a Partially Used Transfer Ribbon Replacing SuppliesAdding a New Transfer Ribbon Printing in Peel-Mode Printing on Fan-Fold Media Rfid Guidelines Supported Transponders Texas Instruments Tag-it Transponders Philips ICode Transponders Philips ICode BlocksInside Technologies Picotag Transponders Inside Technologies Picotag 2KISO-15693 Transponders ZPL II Commands for Rfid WT Write TagRT Read Tag RT Read Tag RS Rfid Setup RI Rfid Get Tag Unique ID Sample of Rfid Programming WT6FDZebraFS FO100,100A0n,60FN0FS Page Lubrication MaintenanceCleaning Parts List DescriptionPage Replacing the Print Head RemovalCleaning the Print Head Page Printer is not receiving power TroubleshootingResolutions Printer is on and in an idle statePrinter is receiving data Printer has failed its power on self test PostThere is a shortage of memory Either the media or ribbon is outFlash memory is not programmed Print head is under temperaturePrint head is over temperature No print on the label Print Quality ProblemsRibbon sensor settings did not print Printed image does not look rightLabel format was sent to, but not recognized by, the printer Void messages are printed across media Rfid SymptomsRfid tags generally not programmed Nothing is printedManual Calibration Recalibration Troubleshooting TestsPrinting a Configuration Label Resetting the Factory Default Values Communications DiagnosticsPower Off Mode Communications Diagnostics Mode Feed Button ModesPhysical Specifications AppendixMedia Specifications Font/Code Specifications Options Parallel Interface Technical Information Page Index Cable calibrationQuality problems Voltage Write tag command Page