Zebra Technologies R402 manual Appendix, Physical Specifications

Page 61

Appendix

All specifications are subject to change without notice.

Physical Specifications

Size

Weight

7.8inches wide / 6.8 inches tall / 9.4 inches long (depth) 200 mm wide / 173 mm tall / 240 mm long (depth)

3.6 pounds / 1.6 kilograms

Environmental Guidelines

Operating temp.

40 to 104 degrees Fahrenheit / 5 to 40 degrees Celsius

 

 

Operating humidity

10 to 90 percent non-condensing

 

 

Storage temp.

-40 to 140 degrees Fahrenheit / -40 to 60 degrees Celsius

 

 

Storage humidity

5 to 90 percent non-condensing

 

 

Electrical

Autoranging external power supply

 

Input: 100-240VAC; 50-60 Hz

 

Output: 20VDC; 2.5A

 

 

Printing Specifications

 

Print Density

203 dots per inch / 8 dots per millimeter

 

 

 

 

Print Speed

2 inches / 51 millimeters per second

 

 

3 inches / 76 millimeters per second

 

 

4 inches / 102 millimeters per second

 

 

 

 

Print Width

1.0 to 4.09 inches / 25.4 to 104 millimeters

 

 

 

 

Print Length

0.005 to 22 inches / 0.125 to 559 millimeters

 

 

with standard memory

 

 

 

 

Registration

Horizontal: +/- 0.0591 inches (1.5 millimeters)

 

Tolerance

Vertical: +/- 0.0393 inches (1.0 millimeters)

 

 

 

 

FLASH Memory

768K

 

(user available)

 

 

 

 

 

DRAM Memory

1 MB

 

(user available)

 

 

 

 

 

 

 

Image 61
Contents Users Guide R402Page Proprietary Statement Page Contents Operation & Options Appendix 980389-001 Rev. a Hello IntroductionWhat’s in the Box? Opening the printer Inspecting the PrinterInspecting the Printer Closing the printer Reporting Damage Modes of Printing Getting StartedAttaching Power Supply Placing the Roll in the Media Compartment Loading Roll MediaAdjusting the Guides Using the Optional Media Adapter Plates Install the Take-Up Core Install the Ribbon Supply RollLoading Ribbon Attach and Tighten the Ribbon Auto Calibration Operator Controls Power SwitchFeed Button Status LightPrinting a Test Label Parallel Interface Requirements Hooking Up the Printer and ComputerInterface Cable Requirements Adjusting the Print Darkness Adjusting the Print WidthAdjusting the Print Speed Communicating with the PrinterThermal Printing Operation & OptionsAdding a New Transfer Ribbon Replacing SuppliesReplacing a Partially Used Transfer Ribbon Printing in Peel-Mode Printing on Fan-Fold Media Rfid Guidelines Supported Transponders Texas Instruments Tag-it Transponders Philips ICode Blocks Philips ICode TranspondersInside Technologies Picotag 2K Inside Technologies Picotag TranspondersISO-15693 Transponders WT Write Tag ZPL II Commands for RfidRT Read Tag RT Read Tag RS Rfid Setup RI Rfid Get Tag Unique ID Sample of Rfid Programming WT6FDZebraFS FO100,100A0n,60FN0FS Page Cleaning MaintenanceLubrication Description Parts ListPage Removal Replacing the Print HeadCleaning the Print Head Page Resolutions TroubleshootingPrinter is not receiving power Printer is on and in an idle stateThere is a shortage of memory Printer has failed its power on self test PostPrinter is receiving data Either the media or ribbon is outPrint head is over temperature Print head is under temperatureFlash memory is not programmed Ribbon sensor settings did not print Print Quality ProblemsNo print on the label Printed image does not look rightLabel format was sent to, but not recognized by, the printer Rfid tags generally not programmed Rfid SymptomsVoid messages are printed across media Nothing is printedManual Calibration Printing a Configuration Label Troubleshooting TestsRecalibration Communications Diagnostics Resetting the Factory Default ValuesFeed Button Modes Power Off Mode Communications Diagnostics ModeAppendix Physical SpecificationsMedia Specifications Font/Code Specifications Options Parallel Interface Technical Information Page Cable calibration IndexQuality problems Voltage Write tag command Page