Zebra Technologies S-500 manual Cutter Module Disassembly

Page 37

Routine Care and Adjustment

3

Figure 20 Cutter Module Disassembly

II.Disassemble the Cutter Module.

1.See Figure 20. Hold the Cutter Module as illustrated. Put your thumbs on the two Wire Spring Loops and your index fingers on the top of the Rear Cutter Blade Guard. It may help to lay the Cutter Module on a table or other surface throughout this process.

2.To remove the Rear Cutter Blade Guard, first press down simultaneously on the two Wire Spring Loops. While pressing down on the loops, press the Rear Cutter Guard back toward you and over top of the Loops. (You’re trying to tuck the Loops underneath the Blade Guard in this process.)

3.Continue pressing the Rear Cutter Guard toward you and allow the back edge of the Guard to pop up as the Guard comes free from its holders. You may now remove the Rear Cutter Guard by lifting it off of the module.

NOTE: The Wire Springs may flip up out of position during this process. Springs will be repositioned during reassembly.

4.Observe the ends of the Rear Cutter Blade Guard and note the small metal pins protruding toward the inside. During the Reassembly Procedure, these pins will be mounted into the corresponding mounting slots in the Cutter Side Panels.

5.To provide complete access to the area to be cleaned, raise the Upper Cutter Blade Guard as shown in Figure 20.

III. Clean the Cutter Module.

1.Remove any label material which has adhered to the Cutter parts and use a small brush to remove any paper dust from the Cutter Module.

2.If you use pressure-sensitive media, use a lint-free cloth soaked in an adhesive remover to remove all gum and label residue from the Cutting Blades and Guards.

If you use tag stock, use alcohol (part # 01426) to remove any dirt.

This procedure is continued on the next page.

29

Image 37
Contents User’s Guide Proprietary Statement Warranty Information Zebra Software License Agreement Warranty InformationMedia Calibration Adjust the Print Darkness AC Power ON/OFF Switch Fro FEEDServicesKey and Pause Key RS-232 Cabling Requirements Reporting Damage UnpackingGetting Started Printer Power UpSite Requirements Storage and ReshippingVoltage Selection AC Power CableCommunications T t i n g S t a r t e d Tear- Off Mode Media LoadingMedia and Ribbon Loading MediaExternal Rewind Mode Media Loading Cutter Mode Media Loading Cutter Option RequiredFanfold Media Loading Fanfold Media Loading in Tear-Off Mode Peel-Off Mode Media LoadingPeel-Off Option Required Removing the Label Backing Material Peel Off Option Required Non-Continuous Media Adjusting the Media SensorContinuous Media Ribbon Loading Adjusting the Ribbon Supply SpindleRibbon Supply Spindle Normal Position Ribbon Supply Spindle Low-Tension PositionLoading the Ribbon Ribbon RemovalOption Switch Settings Configuration and CalibrationSwitch Baud Rate SwitchMedia Calibration Configuration ModeAdjust the Media Rest Position Adjust the Print DarknessAdjust the Position of the Top of the Label Getting Started Operating Your Zebra Stripe Printer Tear-Off ModePrinter Operating Modes Operation AC Power ON/OFF SwitchOperator Controls AC Power ON/OFF Switch Front Panel Keys Front Panel LightsSensor What it monitors How it works Printer Status SensorsBacking Rewind Spindle Full Sensor Position Format 1 Simple Text and a Barcode Sample ZPL II Label FormatsType this label format Format 2 Saving a Label Format As a Graphic Image Format 3 Using a Serialized Data FieldLine Type this label format You’ll get this printout Type this label format You’ll get this printoutCleaning the Exterior CleaningCleaning the Interior Preventive Maintenance KitCleaning the Printhead Routine Care and AdjustmentCutter Module and Catch Tray Location This procedure is on the next Cutter Module Disassembly This procedure is on Reassembled Cutter Module Lubrication AC Power Fuse ReplacementPrint Quality Adjustments Mechanical AdjustmentsToggle Pressure Adjustment Toggle Pressure AdjustmentRibbon Supply Spindle Adjustment Media Sensor Position AdjustmentBattery Replacement Troubleshooting Table Troubleshooting and DiagnosticsFlashing Troubleshooting and DiagnosticsTroubleshooting and Diagnostics Troubleshooting and Diagnostics Power-On Self Test Printer DiagnosticsAdditional Printer Self Tests Pause Key Self Test Cancel Key Self TestPause Key Self Test Printout Feed Key Self TestMode Key Self Test Extended Printer DiagnosticsFeed Key and Pause Key Page Page Options*Factory-Installed StandardPrinterFonts DefaultPrinterFonts6Dots/mm Page Ard BitmapSmoothFontsPointSizeExamples Zebra Technical Support Bulletin Board Service How to Reach UsTechnical Support Zebra’s Corporate OfficesTechnical Support Service via Telephone Support ServicesTechnical Support via Mail or Fax Zebra Technologies Corporation Service Form Extended Factory Service Agreement Product Service and Support ProgramsThird Party Support And Maintenance Select The Program That Fits Your BusinessUser Self Maintenance Zebra Factory ServicesWang Customer Services Division International Service and Support Zebra Training Programs Course Name Printers Covered Operations and Maintenance CoursesLabeling Bar Codes at WorkSupport Services Printhead Position Adjustment Procedure Adjusting the PrintheadAppendix Print Quality AdjustmentHardware Control Signal Descriptions Signal LevelsPrinter Interface Technical Information RS-232 InterfaceInterconnect To DTE Devices RS-232 Cabling RequirementsInterconnect To DCE Devices Parallel Cabling Requirements Parallel InterfacePin No Parallel Connector Pinout Signal DescriptionsGlossary Glossary Index Index