Nortel Networks 4000, 2600, 1600, 2500, 4500 manual Replacing the system into the chassis

Page 82

82Chapter 6 Contivity 600 Option Installation

1Remove the blank PCI bracket by inserting a Phillips screw driver into the slot at the right of the blank PCI bracket and rotating the screw counter-clockwise.

2Lift out the blank PCI bracket, and slide the replacement card into the intended slot.

Note: Be careful not to bend the copper fingers in the slot.

Make sure the card seats firmly and evenly in the card slot and that the left tabbed-end of the card is seated in its slot. If the card is not seated properly, it will not work.

3Replace the screw at the right end of the PCI bracket.

4Slide the system into the chassis as shown in Figure 40.

Figure 40 Replacing the system into the chassis

I/O

 

 

 

 

 

 

EXPANSION

 

 

 

 

 

 

BAY

 

 

 

 

 

CONSOLE

LAN 1

 

 

 

 

 

 

FD

LAN 0

 

 

 

 

 

RC

 

 

 

 

 

DC

 

 

 

 

 

 

 

 

 

 

 

INPUT

 

 

 

 

 

+12V-

 

 

 

 

 

 

1.7A

 

 

 

 

 

-12V-

 

 

 

 

 

 

0.1A

 

 

 

 

 

+5V-10A

 

 

 

 

 

75W

MAX

CS60004A

5Replace the four Phillips-head screws to secure the bottom panel.

6Reconnect the signal cables.

7Reconnect the power cord to restart the Contivity 600.

302283-E Rev 00

Image 82
Contents Installing Hardware Options for the Contivity VPN Switch Copyright 2001 Nortel Networks USA requirements only Taiwan requirements Canada CS-03 rules and regulations FCC Part 68 compliance statement Nortel Networks Inc. software license agreement Rev Contents Contivity 2600 Option Installation Figures Removing the Contivity 1600 power cord Preface Related publications Text conventionsItalic text Acronyms Hard-copy technical manuals How to get help Technical Solutions Center TelephonePreface Rev Chapter Contivity 4600 Option Installation Opening the ContivityRemoving the Contivity 4600 front bezel Shows the Contivity 4600 front components Contivity 4600 system board layout Sample Contivity 4600 system boardCS460014A Installing Contivity 4600 DIMMs Replacing a Contivity 4600 power supply Installing Contivity 4600 DIMMsRemoving a Contivity 4600 power supply Replacing a Contivity 4600 hard disk drive SoftwareRemoving a Contivity 4600 hard disk drive Software Contivity 4600 Option Installation Rev Chapter Contivity 4500 Option Installation Removing the Contivity 4500 front bezelRemoving the Contivity 4500 front bezel Shows the Contivity 4500 front components Contivity 4500 system board layout Sample Contivity 4500 system board Contivity 4500 Option Installation Bottom to top, in that order Installing Contivity 4500 DIMMs Installing Contivity 4500 DIMMsContivity 4500 Option Installation Replacing a Contivity 4500 power supply Removing a Contivity 4500 power supplyReplacing a Contivity 4500 hard disk drive Removing a Contivity 4500 hard disk drive Chapter Contivity 2500/2000/4000 Option Installation Opening the Contivity 2500/2000/4000Removing the Contivity 2500/2000/4000 front bezel Removing the Contivity 2500/2000/4000 top cover Contivity 2500/2000/4000 system board layout SlotsContivity 2500/2000/4000 Option Installation Installing Contivity 2500/2000/4000 LAN/WAN option cards Installing 2500/2000/4000 LAN/WAN option cardsInstalling Contivity 2500/2000/4000 DIMMs Replacing a Contivity 4000 power supply Installing Contivity 2500/2000/4000 DIMMsRemoving a Contivity 4000 power supply Replacing a Contivity 4000 disk drive Removing a Contivity 4000 hard disk drive Installing Contivity 2500/2000/4000 DIMMs Memory option Contivity 2500/2000/4000 Option Installation Rev Chapter Contivity 2600 Option Installation Removing the Contivity 2600 front bezel Removing the Contivity 2600 top cover Contivity 2600 system board layout Removing the Contivity 2600 top coverContivity 2600 system board Installing LAN/WAN and hardware accelerator option cards Installing LAN/WAN or hardware accelerator cardsContivity 2600 Option Installation Installing Contivity 2600 DIMMs Installing Contivity 2600 DIMMsMemory option Contivity 2600 Option Installation Rev Chapter Contivity 1600 Option Installation Removing the Contivity 1600 front bezel Removing the Contivity 1600 top cover Removing the Contivity 1600 top cover Contivity 1600 system board layout Contivity 1600 system boardInstalling Contivity 1600 option cards Installing Contivity 1600 LAN/WAN option cards Installing Contivity 1600 option cards Installing Contivity 1600 DIMMs Installing Contivity 1600 DIMMsMemory option Chapter Contivity 600 Option Installation Reconnect the power cord to turn the switch back on Removing the bottom screws Contivity 600 system board layout Removing the system from the chassisInstalling Contivity 600 option cards Contivity 600 system boardReplacing the system into the chassis Memory option Contivity 600 Option Installation Rev Index Index