Installation Mounting Locations | Rockford Fosgate 301SP, 401SP

INSTALLATION

MOUNTING LOCATIONS

Engine Compartment

Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will void your warranty.

Trunk Mounting

Mounting the amplifier vertically will provide the best cooling of the amplifier.

Mounting the amplifier on the floor of the trunk will work but provides less cooling capability than vertical mounting.

Mounting the amplifier upside down to the rear deck of the trunk will not provide proper cooling and will severely affect the performance of the amplifier and is strongly not recommended.

Passenger Compartment Mounting

Mounting the amplifier in the passenger compartment will work as long as you provide a sufficient amount of air for the amplifier to cool itself. If you are going to mount the amplifier under the seat of the vehicle, you must have at least 1" (2.54cm) of air gap around the amplifier's heatsink.

Mounting the amplifier with less than 1" (2.54cm) of air gap around the amplifier's heatsink in the passenger compartment will not provide proper cooling and will severely affect the performance of the amplifier and is strongly not recommended.

BATTERY AND CHARGING

Amplifiers will put an increased load on the vehicle's battery and charging system. We recommend checking your alternator and battery condition to ensure that the electrical system has enough capacity to handle the increased load of your stereo system. Stock electrical systems which are in good condition should be able to handle the extra load of any Rockford Fosgate amplifier without problems, although battery and alternator life can be reduced slightly. To maximize the performance of your amplifier, we suggest the use of a heavy duty battery and an energy storage capacitor.

WIRING THE SYSTEM

!CAUTION: If you do not feel comfortable with wiring your new unit, please see your local Authorized Rockford Fosgate Dealer for installation.

!CAUTION: Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

CAUTION: Avoid running power wires near the low level input cables, antenna,

!power leads, sensitive equipment or harnesses. The power wires carry substantial current and could induce noise into the audio system.

1.Plan the wire routing. Keep RCA cables close together but isolated from the amplifier's power cables and any high power auto accessories, especially electric motors. This is done to prevent coupling the noise from radiated electrical fields into the audio signal. When feeding the wires through the firewall or any metal barrier, protect them with plastic or rubber grommets to prevent short circuits. Leave the wires long at this point to adjust for a precise fit at a later time.

2.Prepare the RED wire (power cable) for attachment to the amplifier by stripping 1/2" of insulation from the end of the wire. Insert the bared wire into the B+ terminal and tighten the set screw to secure the cable in place.

NOTE: The B+ cable MUST be fused 18" or less from the vehicle's battery. Install the fuseholder under the hood and prepare the cable ends as stated above. Connections should be water tight.

3.Trim the RED wire (power cable) within 18" of the battery and strip 1/2"of insulation from the end of the wire. Cut the wire loop that is attached to the fuseholder in half and splice the fuse into the power line using appropriate inline connectors. Use the section of cable that was trimmed earlier and connect it to the other end of the fuseholder.

401SP, 301SP specifications

Rockford Fosgate is a name synonymous with high-performance audio equipment, particularly in the automotive sound system market. Among their impressive lineup, the Rockford Fosgate 401SP and 301SP represent excellent choices for car audio enthusiasts looking to enhance their in-car audio experience.

The Rockford Fosgate 401SP is a powerful 4-inch speaker designed to deliver exceptional sound quality. Built with a flex-fit basket design, it enables easy installation in a variety of vehicles, accommodating various mounting locations. One of its standout features is the high-temperature voice coil that can withstand intense heat, ensuring reliability and performance even under demanding conditions. Coupled with a durable polypropylene cone and butyl rubber surround, the 401SP produces clear and balanced audio across a wide frequency range. This speaker is also equipped with a high-efficiency design, allowing it to generate maximum output with minimal power input, making it suitable for systems running on less power.

On the other hand, the Rockford Fosgate 301SP is designed to cater to users seeking a cost-effective yet high-quality audio solution. This 3-inch speaker fits snugly in tighter spaces while still delivering impressive sound performance. Its weather-resistant design makes it ideal for various environments, ensuring that it can withstand elements such as moisture and UV rays. Like its bigger counterpart, the 301SP utilizes a polypropylene cone and rubber surround, ensuring durability and longevity. Additionally, it features a high-performance voice coil that provides efficient power handling, enabling it to reproduce dynamic sounds with clarity.

Both models incorporate Rockford Fosgate’s advanced engineering technologies, including their unique speaker design that enhances sound stage and imaging. Furthermore, the speakers are optimized for use with amplifiers, allowing users to experience deeper bass and crisper highs when integrated into a full audio system. The combination of these features results in an audio experience that stands out for its quality, depth, and clarity.

In conclusion, both the Rockford Fosgate 401SP and 301SP offer unique advantages tailored to different user needs. Whether you prioritize power and depth with the 401SP or seek a compact solution with excellent quality in the 301SP, Rockford Fosgate continues to deliver top-notch audio products that elevate any car's sound system.