Tektronix Phaser 840 setup guide Setting IPX frame types from the front panel

Page 30

4 Novell NetWare Configuration

Verify information and ﬁnish the conﬁguration

After you have entered the conﬁguration information, the Quick Conﬁguration Wizard displays the Conﬁgured Printer Information dialog box, which reports the information you have entered.

1.Verify that the information is correct.

■If the information is correct, click Apply Changes.

■If the information is not correct, click Back to return to previous dialog boxes and correct the information. Click Next to return to the Conﬁgured Printer Information dialog box. Click Apply Changes.

■To exit the wizard and return to the Main window without making any changes, click Cancel.

2.After you click Apply Changes, the printer resets; the changes take effect when the reset is complete.

3.After the reset, you are prompted to print a test page. It is recommended that you print a test page to verify a successful installation. For more information on NetWare conﬁguration and troubleshooting, see the PhaserShare Networking Manual on your printer’s CD-ROM.

Setting IPX frame types from the front panel

1.When the front panel displays READY TO PRINT, press the down-arrow button until Menu is highlighted. Press Select.

2.Press the down-arrow button until Printer Configuration is highlighted. Press Select.

3.Press the down-arrow button until Network Settings is highlighted. Press Select.

4.Press the down-arrow button until NetWare is highlighted. Press Select.

5.Press the down-arrow button until IPX Frame Type is highlighted. Press Select.

6.Press the down-arrow button until the desired frame type is highlighted. Press Select until On is displayed. If desired, you can set more than one frame type.

7.To return the printer to normal operation, press the down-arrow button until Exit is highlighted. Press Select.

24PhaserShare Networking

Image 30

Contents L O R P R I N T E R Page Phaser 840 Color Printer PhaserShare Networking Setup Guide Page Contents Windows NT Setting the Printer’s IP Addressing ParametersPhaserLink Printer Management Software IndexIntroduction UnixBefore you begin network conﬁguration Printing a ConﬁgurationPrinting a Conﬁguration Printer management If you need more information Connecting Your Printer to a Network PhaserShare Series B Ethernet interfaceEthernet connections and indicators Built-in Ethernet connectorPhaserShare Series B Ethernet card 10Base2 Thin Ethernet Ethernet cables and termination10BaseT or 100BaseTx Twisted Pair 10Base5 Thick EthernetPhaserShare Series B Token Ring card Token Ring connections and indicators Ring speed jumper Token Ring conﬁguration Token Ring parametersUsing the conﬁg-TokenRingscript Conﬁguring Token Ring parametersArp Using the PhaserShare Administrator to conﬁgure Token Ring Using PhaserLink software to conﬁgure Token RingPhaserShare Series B LocalTalk card LocalTalk card connections and indicatorsLocalTalk connection LocalTalk connectors, cables, and terminators Connecting to a single computerConnecting Your Printer to a Network PhaserShare Networking EtherTalk, LocalTalk TokenTalk Configuration Conﬁguration overviewFinding the printer’s name in the Chooser Novell NetWare Configuration Installing the PhaserShare Administrator Installation Log on to the ﬁle server Using the Quick Conﬁguration WizardStart the PhaserShare Administrator Select a print serverConﬁgure the printer and set up queues Launch the Quick Conﬁguration WizardSetting IPX frame types from the front panel Verify information and ﬁnish the conﬁgurationTCP/IP Configuration Unix Adding the printer to the host tableAssigning a print queue to the printer Assigning print queues with PhaserPrint for Unix Required remote printer queue namesUnix model ﬁles Example installation for a typical BSD Unix system Sample printcap ﬁle Descriptions of printcap parametersPrinter conﬁguration Listing the contents of unix.tar Extracting ﬁles from unix.tarExtracting the ﬁles Windows 95 PhaserPort Software TCP/IP conﬁguration for a PCSetting the printer’s IP address PhaserPort software installationUsing the installer Create your ﬁrst port and install the driver Installation Completed dialog, click Finish Adding a port for a new printerAdding a port to an existing printer Changing a port’s IP address Windows NT Click Start, Settings, and Printers Add the printerCreating an LPR port Creating an AppleTalk portInstall the driver Name the printer and set up sharingWindows NT creates the printer Select the port where the printer is connected Adding a Windows NT 4.0 driver on an NT 3.51 serverEnter the printer’s name and set up sharing Adding a Windows NT 3.x driver Creating an LPR port Set up sharing Windows NT PhaserShare Networking Setting the Printer’s IP Addressing Parameters Setting IP parameters from the front panel Setting the Printer’s IP Addressing ParametersSetting IP parameters Rarp or Bootp Set the network maskT E Setting IP parameters Dhcp Installing the Dhcp serverSetting up a Dhcp server Open the Network Administration group Supported BOOTP/DHCP ﬁelds Dhcp transactionsSetting IP parameters PostScript utility ﬁle Unix only Running the conﬁg-IPscript Conﬁg-IP ﬁlenameSetting IP parameters PhaserLink Printer Management Software DNS Setting the Printer’s IP Addressing Parameters PhaserLink Printer Management Software Accessing printer information from a browserPhaserLink Printer Management software help ﬁles Conﬁguring PhaserLink HelpAccessing PhaserLink Help Setting printer parameters PhaserLink software pages Information ForwardingDisabling Information Forwarding With config-IP script With config-TokenRingscript IndexRarp Page Printed on recycled paper