Tektronix Phaser 840 setup guide PhaserShare Series B Token Ring card

Page 15

Connecting Your Printer to a Network 2

PhaserShare Series B Token Ring card

The PhaserShare Series B Token Ring port conforms to the IEEE 802.5 standard. With the PhaserShare Series B Token Ring card, you can connect the printer directly to a Token Ring network using shielded twisted pair (STP; IBM Type 1) or unshielded twisted pair (UTP; IBM Type 3) cables. Contact your dealer to obtain adapters and cables.

N O T E

To fully comply with EMI speciﬁcations, the use of shielded or screened cables may be required. “Shielded” describes IBM-deﬁned cables used with the DB-9 connector. “Screened” describes cables that are electrically similar to Category 4 UTP, but with an added shield or screen.

When a PhaserShare Series B card is purchased initially with the printer, it is installed at the factory. When a PhaserShare Series B card is purchased later as an upgrade kit, follow the installation instructions that are shipped with the card.

When a PhaserShare Series B Token Ring card is installed in the printer, the printer’s built-in Ethernet connector is disabled.

C A U T I O N

To avoid damaging the network interface, turn off the printer before making any

Token Ring connections.

Setup Guide

9

Image 15

Contents L O R P R I N T E R Page Phaser 840 Color Printer PhaserShare Networking Setup Guide Page Contents Index Setting the Printer’s IP Addressing ParametersPhaserLink Printer Management Software Windows NTUnix IntroductionBefore you begin network conﬁguration Printing a ConﬁgurationPrinting a Conﬁguration Printer management If you need more information PhaserShare Series B Ethernet interface Connecting Your Printer to a NetworkBuilt-in Ethernet connector Ethernet connections and indicatorsPhaserShare Series B Ethernet card 10Base5 Thick Ethernet Ethernet cables and termination10BaseT or 100BaseTx Twisted Pair 10Base2 Thin EthernetPhaserShare Series B Token Ring card Token Ring connections and indicators Ring speed jumper Token Ring parameters Token Ring conﬁgurationConﬁguring Token Ring parameters Using the conﬁg-TokenRingscriptArp Using PhaserLink software to conﬁgure Token Ring Using the PhaserShare Administrator to conﬁgure Token RingPhaserShare Series B LocalTalk card LocalTalk card connections and indicatorsLocalTalk connection Connecting to a single computer LocalTalk connectors, cables, and terminatorsConnecting Your Printer to a Network PhaserShare Networking Conﬁguration overview EtherTalk, LocalTalk TokenTalk ConfigurationFinding the printer’s name in the Chooser Novell NetWare Configuration Installing the PhaserShare AdministratorInstallation Select a print server Using the Quick Conﬁguration WizardStart the PhaserShare Administrator Log on to the ﬁle serverLaunch the Quick Conﬁguration Wizard Conﬁgure the printer and set up queuesVerify information and ﬁnish the conﬁguration Setting IPX frame types from the front panelTCP/IP Configuration Unix Adding the printer to the host tableAssigning a print queue to the printer Assigning print queues with PhaserPrint for Unix Required remote printer queue namesUnix model ﬁles Example installation for a typical BSD Unix system Descriptions of printcap parameters Sample printcap ﬁlePrinter conﬁguration Listing the contents of unix.tar Extracting ﬁles from unix.tarExtracting the ﬁles TCP/IP conﬁguration for a PC Windows 95 PhaserPort SoftwareSetting the printer’s IP address PhaserPort software installationUsing the installer Create your ﬁrst port and install the driver Adding a port for a new printer Installation Completed dialog, click FinishAdding a port to an existing printer Changing a port’s IP address Windows NT Add the printer Click Start, Settings, and PrintersCreating an AppleTalk port Creating an LPR portInstall the driver Name the printer and set up sharingWindows NT creates the printer Adding a Windows NT 4.0 driver on an NT 3.51 server Select the port where the printer is connectedEnter the printer’s name and set up sharing Adding a Windows NT 3.x driver Creating an LPR port Set up sharing Windows NT PhaserShare Networking Setting the Printer’s IP Addressing Parameters Setting the Printer’s IP Addressing Parameters Setting IP parameters from the front panelSet the network mask Setting IP parameters Rarp or BootpT E Setting IP parameters Dhcp Installing the Dhcp serverSetting up a Dhcp server Open the Network Administration group Dhcp transactions Supported BOOTP/DHCP ﬁeldsSetting IP parameters PostScript utility ﬁle Unix only Conﬁg-IP ﬁlename Running the conﬁg-IPscriptSetting IP parameters PhaserLink Printer Management Software DNS Setting the Printer’s IP Addressing Parameters Accessing printer information from a browser PhaserLink Printer Management SoftwarePhaserLink Printer Management software help ﬁles Conﬁguring PhaserLink HelpAccessing PhaserLink Help Information Forwarding Setting printer parameters PhaserLink software pagesDisabling Information Forwarding Index With config-IP script With config-TokenRingscriptRarp Page Printed on recycled paper