SATO 408e, 412E manual Advanced Mode, Zero Slash YES no, Auto Online YES no, Print Offset

Page 38
DARKNESS RANGE A B

Section 3: Configuration and Operation

3.5 ADVANCED MODE

3.5.1 Advanced

Holding down the LINE button when turning the printer ON causes the printer to go into the Advanced Mode.

ADVANCED MODE

In the following screens of Advanced Mode, you can control the Darkness Range, Zero Slash symbol, Auto Online option, Print Offset, Calendar settings, Ignore CR/LF function, Character Pitch and Head Check feature. Press the FEED button to begin.

3.5.2 Darkness Range

Use this setting to choose between two sets of minimum and maximum achievable darkness levels for printing. Darkness range A is suitable for most types of labels. Darkness range B is higher in

darkness, and can sometimes be use to compensate for light prints. The default setting is A.

Press the LINE button to select A or B, then press the FEED button for the next screen.

3.5.3 Zero Slash

This function works with XU, XS, XM, XB, XL and outline fonts. Select YES to print the digit Zero with a diagonal slash across it. Select NO to use a standard Zero. The default is YES.

ZERO SLASH

YES NO

Press the LINE button to select YES or NO, then press the FEED button for the next screen.

3.5.4 Auto Online

Selecting YES causes the printer to go into ONLINE Mode when it is turned ON. Selecting NO leaves the printer in OFFLINE Mode when it is turned ON. The default setting is YES.

AUTO ONLINE

YES NO

Press the LINE button to select YES or NO, then press the FEED button for the next screen.

3.5.5 Print Offset

This setting defines how many dots vertically and horizontally away from the origin (0,0) to begin printing at. The default value is 0 for both offsets. The valid offset range is:

PRINT OFFSET

V: +0000 H: +000

Vertical:

+0 to +1424 (LM408e)

or

+0 to +2136 (LM412e).

Horizontal:

+0 to +/- 832 (LM408e)

or

+0 to +/-1248 (LM412e).

Press the FEED button move the cursor over each adjustable value, and the LINE button to change it. After setting the offsets, press the FEED button until the following screen appears.

Page 3-10

LM Basic 408e/412e Operator’s Manual

Page 37 Page 39
Image 38
Page 37 Page 39
Contents LM Basic 408e/412e 438A Alexandra Road #05-01/04 Alexandra Technopark Singapore Table of Contents Counters Mode Table of Contents CON’TD Optional Accessories Overview General Specifications Key Feature LM408e and LM412eGeneral Specifications CONT’D SpecificationLabels and Ribbons available Model Name Barcodes Physical Characteristics Dimensions This page is intentionally left blank Installation Printer Placement Tips Electrical PrecautionsGeneral Precautions Installation Unpacking Power cable Operator’s Manual Accessory CD-ROM Included AccessoriesGlobal Warranty Additional information Document Installation Parts Identification Identifying the Main Printer Parts8888888888888888 Parts Identification CONT’DInstallation Loading the Carbon Ribbon Roll Paper Characteristics Loading LabelsMain Cover Label Holder Label Guide Plate Installation Loading Labels CONT’DLoading Roll Paper LabelLoading Fanfold Paper Installation Loading Labels and Tags CONT’D Adjusting the Paper SensorReplacing the Print Head Installation Configuration and Operation Operating ModesOperation Panel Offset Pitch DSWAccessing the Various Printer Modes Accessing the Various Printer Modes CONT’D DSWOverview of LCD Menu Options in Various Modes Overview of LCD Menu Options in Various Modes CONT’D Overview of LCD Menu Options in Various Modes CONT’D Pause Normal ModesOnline OfflineNormal Modes CONT’D Zero Slash YES no Advanced ModeAdvanced Mode Auto Online YES noHead Check Normal Barcode Advanced Mode CONT’DCharacter Pitch Prop Fixed Service Mode Select Language English Service Mode CONT’DPriority Setting Command LCD Ignore CAN/DLE YES noNormal Slow Ribbon Near END Enable DisableACK Signal Counters Mode Counters ModeMove Mode Cont Tear Move ModeMove Mode Pitch Sensor On OFFTest Print Size Xxcm Test Print ModeTest Print Mode Configuration Print Size Small LargeDefault Setting YES no Default Setting ModeResetting the Printer Reset CompletedUser Download Press Line KEY Waiting User Download Completed ALT. Protocol Default CompleteProtocol Storing Counter Clear None Maintenance ModeCounter Clear None Counter Clear ALL Counter Clear Head Test Print Press Feed KEYCompleatlled Maintenance Mode CONT’DALL Clear Mode LCD Status HEX Dump ModeHex Dump Mode in buffer QTYReady Download ModeFlash Download StartendBoot Download Mode Boot DownloaderWhen to clean with the cleaning sheet Cleaning the Print HEAD, Platen and RollersWhen to clean with a cleaning kit IntroductionHOW to Clean the Printer with a Cleaning SET Print head and RollersHOW to Clean the Printer Cleaning Sheet Adjusting Print Quality Adjusting Print DarknessReplacing a Blown Fuse Adjusting Print Quality CONT’DAdjusting Print Speed PR INT SpeedThis page is intentionally left blank Interface Specifications Interface TypesInterface Card DIP Switch Settings RS-232C FunctionInterface Card DIP Switch Settings LAN Interface Card DIP Switch Settings Wireless LANBasic Specifications External Signal InterfaceSerial Interface Specifications RS-232C READY/BUSY Pin AssignmentsTiming Chart Normal Processing Single JOB BufferMulti JOB Buffer Input/Output Signals ON/X-OFFXON XO FF XO N Xoff XO N XO FF Ieee 1284 Interface DIPSW2-5Ieee 1284 Interface CONT’D Pin AssignmentInterface Signals Pin no Signal Type ContentInitial Timing Chart Procedure during Paper End Single JOB Buffer CONT’DTiming Chart Normal Process Printer Status Nline Offline This page is intentionally left blank Initial Checklist ObservationsInterface Specifications if necessary Using the RS232C Serial InterfaceTion 5 Interface Specifications Understanding the LCD Error Messages Status Message on Error Cause SolutionTroubleshooting Guide Symptom Paper is fed but not printedTroubleshooting Guide CONT’D Symptom Low quality print Are the paper and carbon ribbon Optional Accessories Available Interface BoardsHigh speed RS-232C board Optional Accessories Interface Boards1 RS-232C board IEEE-1284 board USB boardCalendar IC Optional Accessories OthersLAN board
Related manuals
Manual 102 pages 38.7 Kb

412E, 408e specifications

The SATO 408e is a high-performance thermal transfer printer that stands out in the world of barcode and label printing, particularly known for its reliability and versatility. Designed for various industrial applications, this printer is well-suited for environments that require durable and efficient printing solutions.

One of the main features of the SATO 408e is its superior print quality. It utilizes advanced thermal transfer technology, allowing for crisp and clear printing at speeds of up to 10 inches per second. The printer is capable of producing sharp barcodes, text, and graphics, ensuring that labels meet high standards for readability and durability.

The SATO 408e supports a wide range of media types and sizes, accommodating labels from 0.63 inches to 4.1 inches in width. This flexibility makes it an ideal choice for industries such as manufacturing, logistics, healthcare, and retail, where diverse labeling needs may arise. Whether you need labels for shipping, inventory management, or patient identification, the SATO 408e can handle it all.

Another significant characteristic of the SATO 408e is its user-friendly interface. The printer features an intuitive LCD screen that simplifies navigation through the printer’s settings. Additionally, it includes easy-to-access components for media and ribbon loading, allowing for quick replacement and minimal downtime. This ergonomic design caters to various user levels, from novices to seasoned operators.

Connectivity options are also a strong point for the SATO 408e. It comes equipped with multiple connectivity interfaces, including USB, Ethernet, and serial ports, providing flexibility in how the printer can be integrated into existing systems. This seamless integration allows for enhanced workflow efficiency and adaptability to different business setups.

Furthermore, the SATO 408e incorporates advanced monitoring and maintenance features. It supports real-time monitoring of printer status and media usage, enabling proactive management and reducing the risk of interruptions during print runs.

In conclusion, the SATO 408e thermal transfer printer is characterized by its high print quality, versatility in media handling, user-friendly design, and robust connectivity options. It is a reliable solution for businesses that demand precision and efficiency in their labeling processes, making it a leading choice among industrial printers in the market today.
Top Page Image Contents