SATO 412E, 408e Test Print Mode Configuration, Test Print Size Xxcm, Print Size Small Large

Page 45

Section 3: Configuration and Operation

3.9 TEST PRINT MODE

3.9.1 Select Test Print

In this mode, you can choose from five types of test prints. The five settings in this mode are as follows:

TEST PRINT MODE CONFIGURATION

Use the LINE button to select the test print pattern to generate, the press the FEED button to confirm the setting and proceed to the next screen.

3.9.2 Test Print Size

In this screen you can specify the print width for all the test print patterns except MEMORY. The default setting is the maximum horizontal size of the loaded paper.

TEST PRINT SIZE XXCM

For the LM408e/412e, the test print paper width can be set from 4 to 10.

Use the LINE button to select modify the value of the print size, then press the FEED button to confirm the setting and proceed to the next screen.

3.9.3 Print Size

For the Factory Test Print pattern, this screen lets you define the test print paper width. The default value for the LM408e/412e is LARGE (104mm). The preset value for SMALL is 30mm.

PRINT SIZE SMALL LARGE

Use the LINE button to select either SMALL or LARGE. Then press the FEED button to confirm the setting and proceed to the final screen.

3.9.3 Start/Stop Test Print

At this screen the test printing will have commenced. Press FEED to stop or restart the printing.

PRESS FEED KEY TO STOP PRINTING

LM Basic 408e/412e Operator’s Manual

Page 3-17

Page 44 Page 46
Image 45
Page 44 Page 46
Contents LM Basic 408e/412e 438A Alexandra Road #05-01/04 Alexandra Technopark Singapore Table of Contents Counters Mode Table of Contents CON’TD Optional Accessories Overview Key Feature LM408e and LM412e General SpecificationsSpecification General Specifications CONT’DLabels and Ribbons available Model Name Barcodes Physical Characteristics Dimensions This page is intentionally left blank Installation Electrical Precautions Printer Placement TipsGeneral Precautions Installation Unpacking Included Accessories Global Warranty Additional information DocumentPower cable Operator’s Manual Accessory CD-ROM Identifying the Main Printer Parts Installation Parts IdentificationParts Identification CONT’D 8888888888888888Installation Loading the Carbon Ribbon Loading Labels Roll Paper CharacteristicsLoading Roll Paper Installation Loading Labels CONT’DMain Cover Label Holder Label Guide Plate LabelLoading Fanfold Paper Adjusting the Paper Sensor Installation Loading Labels and Tags CONT’DReplacing the Print Head Installation Operating Modes Configuration and OperationOffset Pitch DSW Operation PanelAccessing the Various Printer Modes DSW Accessing the Various Printer Modes CONT’DOverview of LCD Menu Options in Various Modes Overview of LCD Menu Options in Various Modes CONT’D Overview of LCD Menu Options in Various Modes CONT’D Online Normal ModesPause OfflineNormal Modes CONT’D Advanced Mode Advanced ModeZero Slash YES no Auto Online YES noAdvanced Mode CONT’D Character Pitch Prop FixedHead Check Normal Barcode Service Mode Priority Setting Command LCD Service Mode CONT’DSelect Language English Ignore CAN/DLE YES noRibbon Near END Enable Disable ACK SignalNormal Slow Counters Mode Counters ModeMove Mode Move ModeMove Mode Cont Tear Pitch Sensor On OFFTest Print Mode Configuration Test Print ModeTest Print Size Xxcm Print Size Small LargeResetting the Printer Default Setting ModeDefault Setting YES no Reset CompletedUser Download Completed ALT. Protocol Default Complete Protocol StoringUser Download Press Line KEY Waiting Counter Clear None Counter Clear ALL Counter Clear Head Maintenance ModeCounter Clear None Test Print Press Feed KEYMaintenance Mode CONT’D ALL Clear ModeCompleatlled Hex Dump Mode in buffer HEX Dump ModeLCD Status QTYFlash Download Download ModeReady StartendBoot Downloader Boot Download ModeWhen to clean with a cleaning kit Cleaning the Print HEAD, Platen and RollersWhen to clean with the cleaning sheet IntroductionPrint head and Rollers HOW to Clean the Printer with a Cleaning SETHOW to Clean the Printer Cleaning Sheet Adjusting Print Darkness Adjusting Print QualityAdjusting Print Speed Adjusting Print Quality CONT’DReplacing a Blown Fuse PR INT SpeedThis page is intentionally left blank Interface Types Interface SpecificationsFunction Interface Card DIP Switch Settings RS-232CInterface Card DIP Switch Settings Wireless LAN Interface Card DIP Switch Settings LANExternal Signal Interface Serial Interface Specifications RS-232CBasic Specifications Pin Assignments READY/BUSYSingle JOB Buffer Timing Chart Normal ProcessingMulti JOB Buffer ON/X-OFF Input/Output SignalsXON XO FF XO N Xoff XO N XO FF DIPSW2-5 Ieee 1284 InterfacePin Assignment Ieee 1284 Interface CONT’DPin no Signal Type Content Interface SignalsInitial Single JOB Buffer CONT’D Timing Chart Procedure during Paper EndTiming Chart Normal Process Printer Status Nline Offline This page is intentionally left blank Observations Initial ChecklistUsing the RS232C Serial Interface Tion 5 Interface SpecificationsInterface Specifications if necessary Status Message on Error Cause Solution Understanding the LCD Error MessagesSymptom Paper is fed but not printed Troubleshooting GuideTroubleshooting Guide CONT’D Symptom Low quality print Are the paper and carbon ribbon Available Interface Boards Optional AccessoriesOptional Accessories Interface Boards 1 RS-232C boardHigh speed RS-232C board USB board IEEE-1284 boardOptional Accessories Others LAN boardCalendar IC
Related manuals
Manual 102 pages 38.7 Kb

412E, 408e specifications

The SATO 408e is a high-performance thermal transfer printer that stands out in the world of barcode and label printing, particularly known for its reliability and versatility. Designed for various industrial applications, this printer is well-suited for environments that require durable and efficient printing solutions.

One of the main features of the SATO 408e is its superior print quality. It utilizes advanced thermal transfer technology, allowing for crisp and clear printing at speeds of up to 10 inches per second. The printer is capable of producing sharp barcodes, text, and graphics, ensuring that labels meet high standards for readability and durability.

The SATO 408e supports a wide range of media types and sizes, accommodating labels from 0.63 inches to 4.1 inches in width. This flexibility makes it an ideal choice for industries such as manufacturing, logistics, healthcare, and retail, where diverse labeling needs may arise. Whether you need labels for shipping, inventory management, or patient identification, the SATO 408e can handle it all.

Another significant characteristic of the SATO 408e is its user-friendly interface. The printer features an intuitive LCD screen that simplifies navigation through the printer’s settings. Additionally, it includes easy-to-access components for media and ribbon loading, allowing for quick replacement and minimal downtime. This ergonomic design caters to various user levels, from novices to seasoned operators.

Connectivity options are also a strong point for the SATO 408e. It comes equipped with multiple connectivity interfaces, including USB, Ethernet, and serial ports, providing flexibility in how the printer can be integrated into existing systems. This seamless integration allows for enhanced workflow efficiency and adaptability to different business setups.

Furthermore, the SATO 408e incorporates advanced monitoring and maintenance features. It supports real-time monitoring of printer status and media usage, enabling proactive management and reducing the risk of interruptions during print runs.

In conclusion, the SATO 408e thermal transfer printer is characterized by its high print quality, versatility in media handling, user-friendly design, and robust connectivity options. It is a reliable solution for businesses that demand precision and efficiency in their labeling processes, making it a leading choice among industrial printers in the market today.
Top Page Image Contents