SATO 408e, 412E manual Maintenance Mode, Counter Clear None Counter Clear ALL Counter Clear Head

Page 48

Section 3: Configuration and Operation

3.12 MAINTENANCE MODE

3.12.1 Factory or All Clear Mode

In this mode, the status of DSW2-4 determines whether you can access the Factory mode or the All Clear Mode. Set DSW2-4=ON first. Then the printer will remain Maintenance Mode until the DSW2-4 is set to OFF.

COUNTERS MODE

In the Factory Mode settings, you can change the following: Counter Clear, Print Size for test print width, and Start/Stop test print. In All Clear settings, you can clear the Counter/EEPROM.

3.12.2 Factory Mode

In this screen you can choose to perform an All Clear for all the counters, or clear on the Head Counter.

The default value is NONE. Use the LINE button to select NONE, ALL or HEAD as required.

Press the FEED button to confirm the reset and proceed to the next screen.

COUNTER CLEAR NONE

COUNTER CLEAR ALL

COUNTER CLEAR HEAD

3.12.3 Test-Print Width

In this screen you can choose either a SMALL or LARGE test print. The default value is LARGE.

COUNTER CLEAR NONE

On the LM408e/412e, the value for SMALL is 40mm, and for LARGE, the value is 104mm.

Use the LINE button to select SMALL or LARGE, then press the FEED button to confirm the setting and proceed to the test print.

3.12.4 Start/Stop Test Print

This screen appears during the actual test printing.

Press the FEED button to stop or resume the test printing.

TEST PRINT PRESS FEED KEY

Page 3-20

LM Basic 408e/412e Operator’s Manual

Page 47 Page 49
Image 48
Page 47 Page 49
Contents LM Basic 408e/412e 438A Alexandra Road #05-01/04 Alexandra Technopark Singapore Table of Contents Counters Mode Table of Contents CON’TD Optional Accessories Overview General Specifications Key Feature LM408e and LM412eGeneral Specifications CONT’D SpecificationLabels and Ribbons available Model Name Barcodes Physical Characteristics Dimensions This page is intentionally left blank Installation Printer Placement Tips Electrical PrecautionsGeneral Precautions Installation Unpacking Included Accessories Global Warranty Additional information DocumentPower cable Operator’s Manual Accessory CD-ROM Installation Parts Identification Identifying the Main Printer Parts8888888888888888 Parts Identification CONT’DInstallation Loading the Carbon Ribbon Roll Paper Characteristics Loading LabelsInstallation Loading Labels CONT’D Loading Roll PaperMain Cover Label Holder Label Guide Plate LabelLoading Fanfold Paper Installation Loading Labels and Tags CONT’D Adjusting the Paper SensorReplacing the Print Head Installation Configuration and Operation Operating ModesOperation Panel Offset Pitch DSWAccessing the Various Printer Modes Accessing the Various Printer Modes CONT’D DSWOverview of LCD Menu Options in Various Modes Overview of LCD Menu Options in Various Modes CONT’D Overview of LCD Menu Options in Various Modes CONT’D Normal Modes OnlinePause OfflineNormal Modes CONT’D Advanced Mode Advanced ModeZero Slash YES no Auto Online YES noAdvanced Mode CONT’D Character Pitch Prop FixedHead Check Normal Barcode Service Mode Service Mode CONT’D Priority Setting Command LCDSelect Language English Ignore CAN/DLE YES noRibbon Near END Enable Disable ACK SignalNormal Slow Counters Mode Counters ModeMove Mode Move ModeMove Mode Cont Tear Pitch Sensor On OFFTest Print Mode Test Print Mode ConfigurationTest Print Size Xxcm Print Size Small LargeDefault Setting Mode Resetting the PrinterDefault Setting YES no Reset CompletedUser Download Completed ALT. Protocol Default Complete Protocol StoringUser Download Press Line KEY Waiting Maintenance Mode Counter Clear None Counter Clear ALL Counter Clear HeadCounter Clear None Test Print Press Feed KEYMaintenance Mode CONT’D ALL Clear ModeCompleatlled HEX Dump Mode Hex Dump Mode in bufferLCD Status QTYDownload Mode Flash DownloadReady StartendBoot Download Mode Boot DownloaderCleaning the Print HEAD, Platen and Rollers When to clean with a cleaning kitWhen to clean with the cleaning sheet IntroductionHOW to Clean the Printer with a Cleaning SET Print head and RollersHOW to Clean the Printer Cleaning Sheet Adjusting Print Quality Adjusting Print DarknessAdjusting Print Quality CONT’D Adjusting Print SpeedReplacing a Blown Fuse PR INT SpeedThis page is intentionally left blank Interface Specifications Interface TypesInterface Card DIP Switch Settings RS-232C FunctionInterface Card DIP Switch Settings LAN Interface Card DIP Switch Settings Wireless LANExternal Signal Interface Serial Interface Specifications RS-232CBasic Specifications READY/BUSY Pin AssignmentsTiming Chart Normal Processing Single JOB BufferMulti JOB Buffer Input/Output Signals ON/X-OFFXON XO FF XO N Xoff XO N XO FF Ieee 1284 Interface DIPSW2-5Ieee 1284 Interface CONT’D Pin AssignmentInterface Signals Pin no Signal Type ContentInitial Timing Chart Procedure during Paper End Single JOB Buffer CONT’DTiming Chart Normal Process Printer Status Nline Offline This page is intentionally left blank Initial Checklist ObservationsUsing the RS232C Serial Interface Tion 5 Interface SpecificationsInterface Specifications if necessary Understanding the LCD Error Messages Status Message on Error Cause SolutionTroubleshooting Guide Symptom Paper is fed but not printedTroubleshooting Guide CONT’D Symptom Low quality print Are the paper and carbon ribbon Optional Accessories Available Interface BoardsOptional Accessories Interface Boards 1 RS-232C boardHigh speed RS-232C board IEEE-1284 board USB boardOptional Accessories Others LAN boardCalendar IC
Related manuals
Manual 102 pages 38.7 Kb

412E, 408e specifications

The SATO 408e is a high-performance thermal transfer printer that stands out in the world of barcode and label printing, particularly known for its reliability and versatility. Designed for various industrial applications, this printer is well-suited for environments that require durable and efficient printing solutions.

One of the main features of the SATO 408e is its superior print quality. It utilizes advanced thermal transfer technology, allowing for crisp and clear printing at speeds of up to 10 inches per second. The printer is capable of producing sharp barcodes, text, and graphics, ensuring that labels meet high standards for readability and durability.

The SATO 408e supports a wide range of media types and sizes, accommodating labels from 0.63 inches to 4.1 inches in width. This flexibility makes it an ideal choice for industries such as manufacturing, logistics, healthcare, and retail, where diverse labeling needs may arise. Whether you need labels for shipping, inventory management, or patient identification, the SATO 408e can handle it all.

Another significant characteristic of the SATO 408e is its user-friendly interface. The printer features an intuitive LCD screen that simplifies navigation through the printer’s settings. Additionally, it includes easy-to-access components for media and ribbon loading, allowing for quick replacement and minimal downtime. This ergonomic design caters to various user levels, from novices to seasoned operators.

Connectivity options are also a strong point for the SATO 408e. It comes equipped with multiple connectivity interfaces, including USB, Ethernet, and serial ports, providing flexibility in how the printer can be integrated into existing systems. This seamless integration allows for enhanced workflow efficiency and adaptability to different business setups.

Furthermore, the SATO 408e incorporates advanced monitoring and maintenance features. It supports real-time monitoring of printer status and media usage, enabling proactive management and reducing the risk of interruptions during print runs.

In conclusion, the SATO 408e thermal transfer printer is characterized by its high print quality, versatility in media handling, user-friendly design, and robust connectivity options. It is a reliable solution for businesses that demand precision and efficiency in their labeling processes, making it a leading choice among industrial printers in the market today.
Top Page Image Contents