Transcend Information TS64GSSD25-S dimensions Standby E2h, Standby Immediate E0h, Write Buffer E8h

Page 28

TS8GSSD25-S

 

TS16GSSD25-S

 

TS32GSSD25-S/M

 

TS64GSSD25-S/M

2.5” Solid State Disk

TS128GSSD25-M

STANDBY (E2h)

This command causes the device to set BSY, enter the Sleep mode (which corresponds to the ATA “Standby” Mode), clear BSY and return the interrupt immediately.

STANDBY IMMEDIATE (E0h)

This command causes the drive to set BSY, enter the Sleep mode (which corresponds to the ATA “Standby” Mode), clear BSY and return the interrupt immediately.

WRITE BUFFER (E8h)

This command enables the host to write the contents of one 512-byte block of data to the device’s buffer.

WRITE DMA (CAh)

Write data to sectors during Ultra DMA and Multiword DMA transfer. Use the SET FEATURES command to specify the mode value.

WRITE DMA EXT (35h)

48-bit feature set mandatory command. Write data to sectors during Ultra DMA and Multiword DMA transfer. Use the SET FEATURES command to specify the mode value.

WRITE DMA FUA EXT (3Dh)

48-bit feature set mandatory command. This command provides the same function as the WRITE DMA EXT command except that regardless of whether volatile and/or non-volatile write caching in the device is enabled or not, the user data shall be written to non-volatile media before command completion is reported.

WRITE FPDMA QUEUED (61h)

NCQ feature set mandatory 48-bit command. This command causes data to be transferred from the host to the device.

WRITE MULTIPLE (C5h)

This command is similar to the Write Sectors command. Interrupts are not presented on each sector, but on the transfer of a block which contains the number of sectors defined by Set Multiple command.

Transcend Information Inc.

28

V1.08

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Placement Features DimensionsDescription V1.08Specifications Sequential WriteMax Model P/N Sequential ReadMaxModel P/N User Max. LBA Cylinder Head Sector Operating Non-Operating Data Reliability Data RetentionCompliance Package Dimensions TS128GSSD25-MPin Layout Pin AssignmentsPin No Pin Name Block Diagram Reliability Wear-Leveling algorithmECC algorithm Bad-block managementSupport ATA/ATAPI Command List Command Name CodeSET Multiple Mode ATA Command Specifications Identify Device Information Default Value Word Value DescriptionPIO data transfer cycle timing mode Reserved TS8GSSD25-S TS16GSSD25-S TS32GSSD25-S/M TS64GSSD25-S/M Minor version number TS8GSSD25-S TS16GSSD25-S TS32GSSD25-S/M TS64GSSD25-S/M TS8GSSD25-S TS16GSSD25-S TS32GSSD25-S/M TS64GSSD25-S/M TS8GSSD25-S TS16GSSD25-S TS32GSSD25-S/M TS64GSSD25-S/M Idle E3h Idle Immediate E1hInitialize Device Parameters 91h Read Buffer E4hLog Address Log Name Feature Set Access Read LOG EXT 2FhRead Multiple C4h Read Multiple EXT 29hSecurity Disable Password F6h Recalibrate 10hSecurity Erase Prepare F3h Security Erase Unit F4hSecurity set Password data content Security Unlock informationFeatures register Value and settable operating mode D9h DAhByte Description Byte 2-361 Individual attribute dataAttribute ID information is listed in the following table Description Detail Information ByteSmart Read Attribute Threshold Smart Enabl Operations Standby E2h Standby Immediate E0hWrite Buffer E8h Write DMA CAhWrite Multiple EXT 39h Write Multiple FUA EXT CEhWrite Sectors 30h/31h Write Sectors EXT 34hTranscend Information Inc Ultra DMA data transferUltra DMA data burst timing requirements Name Comment Initiating an Ultra DMA data-in burst Host pausing an Ultra DMA data-in burst Sustained Ultra DMA data-in burstDevice terminating an Ultra DMA data-in burst Host terminating an Ultra DMA data-in burst Initiating an Ultra DMA data-out burst Device pausing an Ultra DMA data-out burst Sustained Ultra DMA data-out burstHost terminating an Ultra DMA data-out burst Device terminating an Ultra DMA data-out burst PIO data transfer PIO timing requirementsPIO data transfer to/from device Ordering Information Taiwan Germany
Top Page Image Contents