Galaxy PWTM 100 to 225 kVA
■ total time with Tbatt > 25° C (h): this |
is the total time of operation with the bat- |
tery temperature greater than 25° C since |
initial startup of the UPS. It is expressed in |
hours; |
■ last reset: this is the date that the infor- |
mation was last set to zero by the |
Teleservice function; |
■ elapsed backup time (min): this is the |
total time of operation on battery power |
since the last reset. It is expressed in min- |
utes. |
■ nb of backups: this is the number of |
times the load was supplied by the UPS |
from battery power since the last reset; |
■ nb of backups < 1 min: this is the |
number of times the load was supplied by |
the UPS from battery power for less than |
one minute, since the last reset; |
■ 1 min < nb of backups < 3 min: this is |
the number of times the load was supplied |
Use the ▼ and ▼ keys to shift between the beginning and the end of the display.
FIGURES SINCE | RESET |
|
| ||
nb of | backups: |
|
|
| 0 |
nb of | backups | < | 1 min: | 0 | |
1 min | < nb of backups < 3 min: | 0 | |||
nb of | backups | > | 3 min: | 0 | |
nb of | overloads | < 5 | s: | 0 | |
nb of | overloads | > 5 | s: | 0 | |
nb of | times TBatt. > | 25°C: | 0 |
by the UPS from battery power for more |
than one minute and less than three min- |
utes, since the last reset; |
consulting recorded measurements
Recorded measurements are presented in the same manner (see opposite):
■nb of backups > 3 min: this is the number of times the load was supplied by the UPS from battery power for more than three minutes, since the last reset;
■nb of overloads < 5 s: this is the num- ber of times the UPS was overloaded (out- put current greater than In) for less than five seconds, since the last reset;
■nb of overloads > 5 s: this is the num- ber of times the UPS was overloaded (out- put current greater than In) for more than five seconds, since the last reset;
■nb of times TBatt. > 25° C: this is the number of times the battery temperature was measured at over 25° C, since the last reset.
■the lists indicate the last 30 measure- ments recorded for the given parameter. The chronological order of the measure- ments is indicated in the figure opposite;
■the most recent measurement is pre- sented first, in the upper
■the period T between two successive measurements is 30 days. The displayed measurements are instantaneous values.
NOTE
when this screen is selected, approximately ten seconds are required to call up and display the information.
If the number of mea- surements is greater than 30, only the last 30 (the most recent) are dis- played
PARAMETER NAME (units) | T=30 days |
▼last read: 05/09/1997
M(t+29T)M(t+23T)M(t+17T)M(t+11T)M(t+05T)
M(t+28T)M(t+22T)M(t+16T)M(t+10T)M(t+04T)
M(t+27T)M(t+21T)M(t+15T)M(t+09T)M(t+03T)
M(t+26T)M(t+20T)M(t+14T)M(t+08T)M(t+02T)
M(t+25T)M(t+19T)M(t+13T)M(t+07T) M(t+T)
M(t+24T)M(t+18T)M(t+12T)M(t+06T) M(t)
26 | Logging and |