American Power Conversion VS 100, VS 50 user manual Alarm Summary

Page 46

 

 

 

7

Alarm Summary

 

 

 

 

 

 

ALARM/

DESCRIPTION

DEFAULT SETTINGS

 

 

[MENU LOCATION]

 

 

 

 

Battery Discharge Alarm

The battery discharge current exceeds

Minor

 

 

[Batteries/Parameters]

the programmed battery discharge

 

 

 

 

 

threshold.

 

 

 

Battery High Temp Alm

The battery temperature exceeds the

Minor

 

 

[Batteries/Parameters]

Battery High Temperature threshold.

 

 

 

Battery Low Temp Alm

The Battery Temperature is below the

Minor

 

 

[Batteries/Parameters]

battery Low Temperature threshold.

 

 

 

Battery LV Alm

The dc output voltage is below the

Major

 

 

[Batteries/Parameters]

battery low voltage threshold.

 

 

 

Circuit Breaker Alm 1

The top Circuit Breaker in the top shelf is

Major

 

 

[Distribution/Breakers]

tripped.

 

 

 

Circuit Breaker Alm 2

The bottom Circuit Breaker in the top

Major

 

 

[Distribution/Breakers]

shelf is tripped

 

 

 

Circuit Breaker Alm 3

The top Circuit Breaker in the bottom

Major

 

 

[Distribution/Breakers]

shelf is tripped.

 

 

 

Circuit Breaker Alm 4

The bottom Circuit Breaker in the bottom

Major

 

 

[Distribution/Breakers]

shelf is tripped

 

 

 

FUSE Alm 1

Any of Fuse 1 through 4 is blown.

Major

 

 

[Distribution/Fuses]

 

 

 

 

FUSE Alm 2

Any of Fuse 5 through 8 is blown.

Major

 

 

[Distribution/Fuses]

 

 

 

 

FUSE Alm 3

Any of Fuse 9 through 12 is blown.

Major

 

 

[Distribution/Fuses]

 

 

 

 

FUSE Alm 4

Any of Fuse 13 through 16 is blown.

Major

 

 

[Distribution/Fuses]

 

 

 

 

Hardware Batt Temp Alm

There is a hardware failure in the battery

Minor

 

 

[Batteries Parameters]

temperature monitoring function.

 

 

 

Hardware Sys Volt Alm

There is a hardware failure in the system

Minor

 

 

[Power Modules/Rectifiers]

voltage monitoring function.

 

 

 

Hardware Sys Temp Alm

There is a hardware failure in the system

Minor.

 

 

[System/DC Parameters]

temperature monitoring function.

 

 

 

System HT Alm

The System Temperature exceeds the

Minor

 

 

[System/DC Parameters]

system high temperature threshold. Not

 

 

 

 

 

the same as battery temperature alarm.

 

 

 

System HV Alm

The System Voltage is above the System

Minor

 

 

[Power Modules/Rectifiers]

High Voltage threshold. Not the same as

 

 

 

 

 

battery high voltage alarm.

 

 

 

Input Relay 1

An external contact closure at the Input

Ignore

 

 

[I/O/Input]

Relay 1 connection.

 

 

 

 

 

 

 

 

 

 

 

 

 

An external contact opening at the Input

 

 

Relay 4 connection.

Ignore

 

 

Input Relay 4

 

 

 

 

[I/O/Input]

 

 

 

 

Magnum VS –48 Vdc User Manual

Page 46

Image 46
Contents Magnum VS Vdc Power Systems Table of Contents Programming Output Relays Table of Figures Page Introduction General InformationAccessories DescriptionPower Distribution Backplane ControlMechanical Installation InstallationUnpacking Equipment AC Power Connections AC ConnectionsAC Power Cord Sets Connecting the Cables Battery ConnectionsPlanning the Battery installation Recommended toBattery Temperature Probe Installation Counter Electro-Motive Force Cemf Cell ConnectionsDC System Grounding 1 Cemf Connection LocationsGMT Fuse Installation Load Protection InstallationCircuit Breaker Installation Load ConnectionsCircuit Breaker Protected Load Connections 30 or 60 a GMT Fuse-protected Load ConnectionsFront Panel DB9 Connection RJ45 Ethernet ConnectorMonitoring and Relay Output Connections Major, Minor and Relay 1 Output ConnectionsOutput Relay 2-6 Connections 1 Interface ConnectionsExternal Alarm Input Connections 2 Output Relay ConnectionsRectifier Module Installation Controller Module InstallationCommissioning Electrical InstallationBattery Visual and Safety Inspection Pre-Commissioning InspectionCommissioning AC Power UpDC Power Up Initial Set-upLVD Test Battery Power UpRectifier Test Circuit Breaker/ Fuse TestFinal Inspection Battery Temperature CompensationOutput Relay Rectifier Management Technical DescriptionSystem Management System Current Monitor System Status and Alarm ReportingLoad Management Circuit BreakersBattery Charging Battery ManagementGMT Fuses Battery Low Voltage Disconnect Battery ProtectionBattery Temperature Monitoring Counter Electro-Motive Force Module ConnectionsExternal Alarm Inputs User Input Controls and IndicatorsAlarm Outputs Output Relays Network Management Card Local & Remote MonitoringDescription OperationController Module Jumpers Controller Module 1 Controller Card Jumper LocationsOperation Using the RS-232 Comm Port Magnum VS ControllerOperation Using the 10/100 BaseT Ethernet Port Settings Default Settings in Bold00 mV Distribution/BreakersDistribution/Fuses Power Modules/RectifiersSystem/Date & Time Batteries ParametersInput SecondsDisable OutputSystem/Out-Rly/Alias Output RelaySeconds, 0.00 seconds System/Preferences LVD Operation Programming Output RelaysEquipment Preventive MaintenanceSystem Visual and Safety Inspection Inspection Test Battery Temperature Test Battery Current TestBattery Preventive Maintenance Procedure Final Inspection Alarm Summary System LT Alm System Temperature is below Minor Magnum VS 100 Power System SpecificationsMagnum VS 50 Power System AC InputDC Output Magnum VS Controller Mechanical EnvironmentalCompliance APC Worldwide Customer Support Non-transferable Warranty Exclusions Terms of WarrantyWarranty Claims