American Power Conversion SURTA1500XL Configuration Settings, Utility Voltage Measurement

Page 8

Configuration Settings

Utility Voltage Measurement

Feature Display

Feature Title

Description

100V

120V

Diagnostic Utility

The UPS has a diagnostic feature that indicates the utility voltage

Voltage

coming into the UPS. The UPS starts a self-test as part of this

118.0

138.2

 

procedure. The self-test does not affect the voltage display. See

108.7

128.8

 

 

“Troubleshooting,” beginning on page 12 for additional informa-

99.3

119.5

 

 

tion.

90.0

110.1

 

 

 

80.6100.8

1.Press and hold the button to view the utility voltage bar graph indicator.

2.After a few seconds, this five-LED Battery Charge indicator will show the utility input voltage.

3.Refer to the appropriate voltage (100 or 120) reading. Values are not listed on the UPS. The actual input voltage is between the displayed value on the list and the next higher value.

Configuration Settings

Settings are adjusted through PowerChute software, optional SmartSlot accessory cards, or in terminal mode.

Function

Factory Default

User Selectable

Description

Choices

 

 

 

 

 

 

 

Automatic

Every 14 days

• Every 7 days

Set the interval at which the UPS will execute a

Self-Test

(336 hours)

(168 hours)

 

self-test.

 

 

• Every 14 days

 

 

 

(336 hours)

 

 

 

 

• On start up only

 

 

 

• No self-test

 

 

 

 

 

 

UPS ID

UPS_IDEN

Up to eight characters

Uniquely identify the UPS, (i.e. server name or

 

 

(alphanumeric)

location) for network management purposes.

 

 

 

 

 

Date of Last

Manufacture Date

mm/dd/yy

 

Reset this date when you replace the battery

Battery

 

 

 

module.

Replacement

 

 

 

 

 

 

 

 

 

Minimum Capacity

0 percent

• 0%

• 60%

Specify the percentage to which batteries will

Before Return from

 

• 15%

• 75%

be charged following a low battery shutdown

Shutdown

 

• 30%

• 90%

before powering connected equipment.

 

 

• 45%

 

 

 

 

 

 

 

Alarm Delay

Enable

• Enable

• Disable

Mute ongoing alarms or disable all alarms per-

 

 

• Mute

 

manently.

 

 

 

 

 

Shutdown Delay

90 seconds

• 0 s

• 360 s

Set the interval between the time when the

 

 

• 90 s

• 450 s

UPS receives a shutdown command and actual

 

 

• 180 s

• 540 s

shutdown.

 

 

• 270 s

• 630 s

 

 

 

 

 

 

8 Smart-UPS RT SURTA1500XL/SURTA1500XLJ/SURTA2000XL Uninterruptible Power Supply User Manual

Image 8
Contents Introduction/Before Installation Contact Information Safety InformationUnpacking and Equipment Placement About this ManualInstallation To Install the UPS in a RackTo Install the UPS as a Tower Configuration To Install the UPS with External Battery PacksConnectors Type Description If Required, Connect the Emergency Power Off EPO Feature  Connect the Battery and Install the Front Bezel For Additional Computer System Security Terminal Mode ConfigurationConnect Power and Start Up the UPS Display Panel Display Panel IndicatorsOperation On Battery Operation LEDConfiguration Settings Utility Voltage MeasurementFunction Factory Default User Selectable Description Choices Storage, Maintenance, Transport, and Service To Install a Replacement BatteryStorage Transporting the UPS to Another LocationBattery Replacement Instructions ServiceTroubleshooting Problem and/or Possible Cause SolutionEquipment There is no utility power Radio Frequency Warning Regulatory Approvals990-1856A 06/2004 Limited WarrantyCopyright Notice