American Power Conversion SURTA2000XL, SURTA1500XLJ user manual Connectors Type Description

Page 3

 

 

Installation

Connectors

Type

Description

 

EPO terminal

The Emergency Power Off (EPO) terminal allows the user to connect

 

 

the UPS to the central EPO system.

 

 

NOTE: Adhere to national and local codes when wiring the EPO switch.

 

TVSS screw

The UPS features a Transient Voltage Surge-suppression (TVSS) screw

 

 

located on the rear panel, for connecting the ground cable on surge sup-

 

 

pression devices such as telephone and network line protectors.

 

 

NOTE: Prior to connecting the grounding cable, disconnect the UPS

from the utility power outlet and turn off the UPS.

 

 

 

 

 

 

 

 

 

 

 

 

 

External battery

Optional Smart-UPS RT external battery packs provide extended run-

 

 

 

 

 

 

 

 

 

 

 

 

 

pack connector

time during power outages. These units support up to ten external bat-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

tery packs.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: See the APC web site, www.apc.com for information on the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

external battery pack, SURTA48XLBP or SURTA48XLBPJ.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PDU Receptacles Connect equipment to the Power Distribution Unit (PDU) receptacles on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the rear of the UPS.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.Connect equipment to PDU receptacles .

2.If applicable, connect equipment to the serial or USB com port .

3.Connect ground cable of voltage surge-suppression equipment or the optional Smart-UPS RT battery pack to the TVSS screw .

4.Add optional accessories to the Smart-Slot .

a.Remove the cover and screws. Discard or save cover. Do not attempt to reinstall it.

b.Refer to the accessory manual to install equipment.

If Required, Connect the Emergency Power Off (EPO) Feature

The EPO interface is a safety extra low voltage (SELV) circuit. Connect it only to other SELV circuits. To avoid damage to the UPS, do not connect the EPO interface to any

Caution circuit other than a closure type circuit, properly isolated from the utility.

Smart-UPS RT SURTA1500XL/SURTA1500XLJ/SURTA2000XL Uninterruptible Power Supply User Manual

3

Image 3
Contents About this Manual Introduction/Before InstallationContact Information Safety Information Unpacking and Equipment PlacementTo Install the UPS with External Battery Packs InstallationTo Install the UPS in a Rack To Install the UPS as a Tower ConfigurationIf Required, Connect the Emergency Power Off EPO Feature Connectors Type Description  Connect the Battery and Install the Front Bezel Terminal Mode Configuration Connect Power and Start Up the UPSFor Additional Computer System Security Display Panel Indicators OperationDisplay Panel LED On Battery OperationUtility Voltage Measurement Configuration SettingsFunction Factory Default User Selectable Description Choices Transporting the UPS to Another Location Storage, Maintenance, Transport, and ServiceTo Install a Replacement Battery StorageService Battery Replacement InstructionsProblem and/or Possible Cause Solution TroubleshootingEquipment There is no utility power Regulatory Approvals Radio Frequency WarningLimited Warranty Copyright Notice990-1856A 06/2004