GBC 3064WF operation manual Pre-Installation, GBC 3064 WF Requires

Page 6

GBC 3064WF

Operation Manual

PRE-INSTALLATION

Before a 3064 Laminator can be installed, ensure the following requirements are met:

1. Are doorways and hallways wide enough for the laminator to be moved to the installation site?

2. Is there ample room for the laminator?

• A work area must be established that allows for operation in both the front and rear of the laminator and provides space for efficient material flow.

3. Is the environment appropriate for the laminator?

• The laminator requires a clean, dust and vapor free environment to operate properly.

• Avoid locating the laminator near sources of heat or cold. Avoid locating the laminator in the direct path of forced, heated or cooled air.

CAUTION: Air flow can cause uneven heating / cooling of the rollers and result in poor output quality.

4. Have you contacted a certified electrician to wire the receptacle and ensure that adequate power is being supplied, having the appropriate capacity, over current protection and safety lockouts available?

GBC 3064 WF Requires:

• 220V at 60Hz with 32 amps single phase.

• Nema 6-50 R 50 A 250 V Receptacle

This Machine is supplied with a Nema 6-50 male

Plug

INSTALLATION

1.Shipping damage should be brought to the immediate attention of the delivering carrier.

2.With assistance, carefully roll the laminator into position over flat and even surfaces.

3.The laminator should be positioned to allow exiting film to flow freely to the floor or a work table. Accumulation of laminate immediately behind the laminator as it exits the equipment may cause the film to wrap around the pull rollers, resulting in a “jammed” condition.

4.Avoid locating the laminator near sources of heat or cold. Avoid locating the laminator in the direct path of forced, heated or cooled air.

5.Once the laminator has been properly positioned, lock the castors in place. Locking the castors prevent the machine from rolling during set up, operation or servicing.

6.Connect the attachment plug provided with the laminator to a suitably grounded outlet. Avoid connecting other equipment to the same branch circuit to which the laminator is connected, as this may result in nuisance tripping of circuit breakers or blowing fuses.

Note: Machine must be leveled to ensure best performance. Level the machine by lowering both the main and pull rolls. Lay A level on top of the main and pull rolls. Then, check level from main roll to pull roll on right and left side of the roll. Finally, check by placing the level diagonally across lower main to lower pull rolls.

© 2005 General Binding Corporation

Page 6

Image 6
Contents ENG GBC 3064WF ENGTable of Contents Service Important Safety InstructionsImportant Safeguards GeneralWarranty SpecificationsPRE-INSTALLATION InstallationGBC 3064 WF Requires Power ON/OFF I/O Control GuideFeatures Guide Media Tables C & 3C Unwind / Rewind ComboRemovable Chill Idler Item a Upper Tension Idler Item a Lower Tension Idler Item BHeated Main Rollers Item a Main On Off I/O SwitchElectronic Safety Beam Item a Swing around control panel arm Item aPull Roll Lift handle Nip Pressure AdjustmentPull Roll Clutch Adjustment Knob Heated Main roll Lift handleSequence of Operations Speed of 3f/mOperating Instructions Film Loading & ThreadingTo load a roll of film Fig Webbing Thermal Film Using Threading Card Webbing PSA Film/Mount Adhesive Using Threading Card Start Laminating Method for Tacking New Film to Existing Film RollersTo unweb the laminator Clearing a Film Jam Wrap-upTo clear a jam Tips for Mounting Pre Coated Boards ApplicationsTips for Pre Coating Boards Tips for Single Sided laminationTips for Creating a Decal Tips for mounting a DecalTips For Thermal Encapsulation Tips for Accushield Speed / Temperature Control ART of LaminationHeat OutputMaintenance Caring For The GBC 3064WF LaminatorService Agreement Tension