GBC 3064WF operation manual Control Guide, Power ON/OFF I/O

Page 7

GBC 3064WF

Operation Manual

CONTROL GUIDE

1

8

9

7

2 a

3

4 b

5

6

1

Figure 5

A. Power ON/OFF (I/O):

Located at the back left of the machine applies power to the laminator. The control panel display will illuminate when position marked “I” is pushed. The Off position, marked “O” removes power from the laminator.

B. Control Panel (Figure 5)

1.Main Roll Nip Pressure relevant pressure in percentage:

2.Top Roll Display

Displays Temperature in “oC “or “oF” of the Top Heater (Both Set Temperature and Current Temperature)

LED Marked “oC” if Illuminated indicates reading in “oC “

LED Marked “oF” if Illuminated indicates Temperature reading in “oF”

LED Marked “Ready” illuminates when set temperature is reached.

{a}. Control Switches:

- When Pressed Increases the Temperature

- When Pressed Decreases the Temperature

MEAS- Press and Hold to Display Current Top Roller

Temperature

3.Main Switch (TOP Heater): When pressed to the

Position turns On the top heater, when pressed to the

Position turns Off the top heater.

4.Bottom Roll Display

Displays Temperature in “oC” or “oF” of the Bottom Heater (Both set Temperature and Current Temperature when MEAS switch is pressed)

LED Marked “oC” if Illuminated indicates reading in “oC”

LED Marked “°F” if Illuminated indicates Temperature reading in “oF”

LED Marked “Ready” illuminates when set temperature is reached.

MEAS- Press and Hold to Display Current Bottom Roller Temperature

{b}. Control Switches

- When Pressed Increases the Temperature

- When Pressed Decreases the Temperature

MEAS-Press and Hold to Display Current Bottom Roller Temperature

5. Main Switch (Bottom Heater): When pressed to the

position turns On the bottom heater, when pressed to the position turns Off the bottom heater.

6.Fan Switch: Switches cooling fan ON / OFF

7. Laminator Main Control Switch:

Switches the

laminator between “RUN” and “STOP”

 

modes.

 

8.Machine Power On Light: Green light illuminated – Machine On.

9.Laminator Direction Motion Control Switch: Controls the forward and rearward movement of the laminator.

10.Laminator Speed Control:

Regulates the speed of laminator feed.

Outer Scale in Feet/Minute.

© 2005 General Binding Corporation

Page 7

Image 7
Contents ENG ENG GBC 3064WFTable of Contents General Important Safety InstructionsImportant Safeguards ServiceSpecifications WarrantyInstallation PRE-INSTALLATIONGBC 3064 WF Requires Control Guide Power ON/OFF I/OFeatures Guide Unwind / Rewind Combo Media Tables C & 3CRemovable Chill Idler Item a Lower Tension Idler Item B Upper Tension Idler Item aSwing around control panel arm Item a Main On Off I/O SwitchElectronic Safety Beam Item a Heated Main Rollers Item aHeated Main roll Lift handle Nip Pressure AdjustmentPull Roll Clutch Adjustment Knob Pull Roll Lift handleSpeed of 3f/m Sequence of OperationsFilm Loading & Threading Operating InstructionsTo load a roll of film Fig Webbing Thermal Film Using Threading Card Webbing PSA Film/Mount Adhesive Using Threading Card Start Laminating Rollers Method for Tacking New Film to Existing FilmClearing a Film Jam Wrap-up To unweb the laminatorTo clear a jam Tips for Single Sided lamination ApplicationsTips for Pre Coating Boards Tips for Mounting Pre Coated BoardsTips for mounting a Decal Tips for Creating a DecalTips For Thermal Encapsulation Tips for Accushield ART of Lamination Speed / Temperature ControlOutput HeatCaring For The GBC 3064WF Laminator MaintenanceTension Service Agreement