Canon 700 manual Troubleshooting, Guide

Page 85

5

Appendix

Troubleshooting

This section describes how to resolve basic printing problems.

Unable to Print from a TCP/IP Network

Cause 1 The machine and network cable are not properly connected.

Remedy

Check all connections, then restart the machine.

 

Check that the machine is connected to the network using the proper cable.

 

(See Chapter 1, “Before You Start Using This Machine,” in the PCL Printer

 

Guide.)

 

The TCP/IP network is not set up properly.

Cause 2

 

 

Remedy

Confirm that the IP addresses are set up properly. Check if the IP addresses

 

are using DHCP, BOOTP, or RARP, and confirm that these protocols are

 

operating.

 

 

Cause 3

The computer that is printing is not set up properly.

 

 

Remedy Check the following:

•Confirm that the proper printer driver has been installed. If you are printing from Windows 95/98/Me, each computer must have a printer driver installed. For instructions on installing printer drivers, see Chapter 1, “Before You Start Using This Machine,” in the PCL Driver Guide.

•Confirm that the correct printer is set as the output destination for the computer that is printing. In Windows 95/98/Me, confirm the output destination for the printer from the Control Panel or Print Manager.

•If you are using LPD with Windows 95/98/Me, confirm that the spooling settings have been made correctly. (See steps 3 to 5 in “Windows 95/98/Me,” on p. 2-23.)

Cause 4 The name of the file being printed is too long.

Remedy Usually LPR (or the Microsoft TCP/IP Printer, if you are using Windows NT/2000/XP), sends jobs either under the name of the application software used for printing, or the specified file name. However, a job name that is longer than 255 characters, cannot be sent to the printer. To correct this, rename the file with a shorter name.

5-2Troubleshooting

Page 84 Page 86
Image 85
Page 84 Page 86
Contents Network Guide Laser Class 700 Series Network Guide PCL Printer Guide PCL Driver Guide Fax Driver Guide Manuals for the MachineBefore You Start How This Manual Is OrganizedContents Using a NetBIOS Network Windows 95/98/Me Using a NetWare Network WindowsAppendix Overview of Network Setting Items Symbols Used in This Manual How to Use This ManualKeys Used in This Manual Abbreviations Used in This Manual Displays Used in This ManualClick OK Trademarks Legal NoticesCopyright Disclaimers Before You Start Printing Using a NetWare Network Printing Using a TCP/IP NetworkSystem Environment Requirements System Requirements for PrintingPrinting Using a NetBIOS Network Sample Windows Network Checking Your Network EnvironmentWithout Using a NetWare Server Sample Unix Network Using a Network with Different Types of Computers 8Checking Your Network Environment Using a TCP/IP Network Windows/UNIX2 Machine, in the PCL Printer Guide TCP/IP Network Setup ProceduresPreparation for Protocol Settings Specifying Protocol SettingsPress or until 6.SYSTEM Settings appears Specifying Network Settings from the Operation PanelOpen all three one-touch speed dialing panels Press SetIf you want to set Dhcp to ‘ON’ or ‘OFF’ If you want to set Rarp to ‘ON’ or ‘OFF’ If you want to set Bootp to ‘ON’ or ‘OFF’To specify the IP address To specify the subnet mask To specify the default gatewayPress or until 5.DNS Server ADD. appears Enter the DNS server address using the numeric keysPress or until 6.DNS Dynamic SET appears Setting the Host Name Setting the Domain Name Data Registration Press or until 4.NETWORK Settings appears Press Stop to return to the Standby modePress Data Registration Open all three one-touch speed dialing panelsPress or to scroll through the settings you want to Using NetSpotPress or until 9.VIEW IP Address appears CheckSet up the web browser to accept cookies Using a Web Browser Remote UISelect Administrator Mode click OK Using a TCP/IP Network Windows/UNIX Specify the IP Address, Subnet Mask, and Gateway Address Specify the LPD settingsFor LPD Print For LPD BannerIf you are using DNS, specify the DNS settings Start up the MS-DOS prompt or the Command prompt Using ARP/PING CommandsClick OK Execute the following command Using an FTP ClientIf a password has been set for the machine Execute the following command to upload the config fileIf no password has been set Enter root as the user nameConnecting to a TCP/IP Network Setting Up a Computer for PrintingWindows 95/98/Me Printer Connection Method LPD/RawOpen the printer’s Properties dialog box Specify the Spool settings Specify the port settings Windows 2000/XP Click OK to enable the settingsIf you are using Windows XP If you are using WindowsAdd Standard TCP/IP Printer Port Wizard starts 30Setting Up a Computer for Printing Click OK to enable the settings If necessary, install Microsoft TCP/IP Printing Check that Microsoft Windows TCP/IP Printing is installedOpen the printer’s Properties dialog box 34Setting Up a Computer for Printing Unix Example using SolarisExample using Turbolinux Example using Red Hat LinuxExample using HP-UX Printer Connection Method IPP Example using IBM-AIXEnter the URL of your printer Start the Add Printer WizardPrinter location settings are complete From the printer’s pop-up menu, display the Sharing sheet Print Server SettingsSpecify the Sharing settings Printer Management Using the Remote UIOperation Command 44Printer Management Using a NetWare Network Windows See NetWare Print Service Settings, on p NetWare Network Setup ProceduresPrint Services NetWare Print Service SettingsNDS Novell Directory Service and Bindery Mode Setup Using NetWare Administrator or Pconsole Specifying Print Service Settings Using NetSpotQueue Server Mode and Remote Printer Mode Enter the print server name in Print Server name Specify the Print Server name, Printer, and Queue settingsSet up a queue assign the print server to the queue Specify the printer name, type, and any remaining items Assign the printer to the print serverAssign a queue to the printer 8NetWare Print Service Settings Protocol Settings 10Protocol Settings Installing the Printer Driver Connecting to a NetWare NetworkPrinter’s Location Setting Specify the printer’s location12Setting Up a Computer for Printing Using a NetBIOS Network Windows 95/98/Me NetBIOS Network Setup Procedures Connecting to a NetBIOS Network To set up the printer’s location, follow the procedure below Specify the Spool settings 6Setting Up a Computer for Printing Click OK to enable the settings 8Setting Up a Computer for Printing Appendix Guide TroubleshootingTroubleshooting 4Troubleshooting LPR Port Utility Deletion How to Uninstall SoftwareClick Yes NetBIOS/NetBEUI Port Monitor Utility DeletionUsing the Operation Panel Overview of Network Setting ItemsUsing NetSpot, Remote UI, or FTP Client System SettingsSetting Description Default Common SettingsTcpframetype TCP/IP SettingsTcpprtcontlist Ncpburstmode NetWare SettingsNetBIOS Settings FTP Available Software for Network SettingsBanding GlossaryBuffer size Container objectDaemon CookieDNS server Domain EthernetInternet Protocol IP Gateway AddressIP address NDS Novell Directory Services NCP Burst ModeNetBIOS Log onPacket Signature Queue Server modeProtocol Proxy serverRIP Raster Image Processor Switching hubScope ID Snmp Simple Network Management ProtocolWAN Vector GraphicsIndex Index Nwadmin Appendix 120V
Related manuals
Manual 358 pages 5.87 Kb Manual 6 pages 32 Kb

700 specifications

The Canon 700, specifically the Canon EOS 700D, is a popular entry-level DSLR that successfully balances user-friendliness with advanced photographic technology. Launched in 2013, this camera serves as a compelling option for beginners and enthusiasts seeking an affordable yet feature-rich device.

One of the standout features of the Canon 700D is its 18-megapixel APS-C CMOS sensor, which offers impressive image quality and detail. This sensor, combined with the DIGIC 5 image processor, allows for quick shooting and great performance in various lighting conditions. The ISO range of 100-12800, expandable to 25600, ensures that users can capture clear and vibrant images, even in low-light environments.

The camera's 3-inch vari-angle touchscreen LCD is another highlight, enabling photographers to compose shots from a variety of angles, enhancing creativity. The touchscreen also streamlines menu navigation and settings adjustment, making it easier for new users to familiarize themselves with the camera's functionalities.

The Canon 700D features an 9-point autofocus system for focusing precision—ideal for both stills and video shooting. This system includes a single cross-type point at the center, which provides enhanced accuracy. Moreover, the camera excels in live view shooting, utilizing a Hybrid CMOS AF system for smooth focusing transitions when capturing moving subjects or shooting video.

Video capabilities are excellent, with the ability to record Full HD 1080p video at a variety of frame rates. Users can take advantage of manual exposure control during video recording, allowing for creative expression and technical expertise in videography.

Connectivity options are also present in the Canon 700D, including a built-in flash, external microphone input, and an HDMI output for easy sharing and playback. Although it lacks built-in Wi-Fi or Bluetooth, the camera can be paired with Wi-Fi-enabled devices via Eye-Fi cards for wireless image transfer.

The Canon 700D is designed with a comfortable grip and an intuitive layout, making it easy to hold for extended periods. This ergonomic design, paired with the camera's relatively lightweight body, makes it a great choice for travel photography.

In summary, the Canon 700D encapsulates technology and ease of use. Its combination of a robust sensor, versatile LCD, and solid video capabilities makes it an ideal option for beginners and those looking to step up their photography skills. Whether shooting landscapes, portraits, or video content, the Canon 700D delivers impressive results.
Top Page Image Contents