Canon 700 RIP Raster Image Processor, Scope ID, Snmp Simple Network Management Protocol, Spooling

Page 102

RIP (Raster Image Processor)

The hardware and/or software functions of a printer that convert vector graphic descriptions from a computer into raster graphic images that can be printed.

Scope ID

The Scope ID is a character string value that is appended to the NetBIOS name, and is used for all NetBIOS over TCP/IP communications. It provides a way for a computer to communicate only with others sharing the same Scope ID.

SMB

Server Message Block. A protocol that provides ﬁle and printer sharing over a network for Windows computers.

SNMP (Simple Network Management Protocol)

The network management protocol of TCP/IP. Agents, which can be hardware or software, monitor the activity of various devices on the network and report to the network console workstation. The information received about each device is maintained in a structure known as a management information block.

Source Routing

Normally, a host has no control over the route taken by a packet it sends. Source routing is a technique whereby the sender of a packet can specify the route that a packet should take through the network to its destination.

Spooling

Simultaneous Peripheral Operations On-Line. Spooling means putting jobs in a buffer, which is a special area in memory or on a disk. Because devices access data at different rates, the buffer provides a waiting station where the data can wait until the device for which it is meant is ready to access it.

Subnet Mask

SUBNETwork mask. The method used to determine which subgroup, or subnet, an IP address belongs to on TCP/IP networks, all devices whose IP addresses have the same preﬁx would belong to the same subnet. Dividing a network into subnets is useful for both security and performance reasons.

Switching hub

A network connection box to which a number of computers can be connected. The switching hub forwards a data packet from the network to the appropriate computer according to the packet’s address. Conventional hubs simply send every packet to every connected computer. Since a switching hub forwards packets only to their intended recipients, it provides greater efﬁciency.

TCP/IP

Acronym for Transmission Control Protocol/Internet Protocol. The protocol used to connect to the Internet and to wide area networks.

5

Appendix

Glossary 5-19

Image 102

Contents Network Guide Laser Class 700 Series Network Guide Manuals for the Machine PCL Printer Guide PCL Driver Guide Fax Driver GuideHow This Manual Is Organized Before You StartContents Using a NetWare Network Windows Using a NetBIOS Network Windows 95/98/MeAppendix Overview of Network Setting Items How to Use This Manual Symbols Used in This ManualKeys Used in This Manual Displays Used in This Manual Abbreviations Used in This ManualClick OK Legal Notices TrademarksCopyright Disclaimers Before You Start System Environment Requirements Printing Using a TCP/IP NetworkPrinting Using a NetWare Network System Requirements for PrintingPrinting Using a NetBIOS Network Checking Your Network Environment Sample Windows NetworkWithout Using a NetWare Server Sample Unix Network Using a Network with Different Types of Computers 8Checking Your Network Environment Using a TCP/IP Network Windows/UNIX2 TCP/IP Network Setup Procedures Machine, in the PCL Printer GuideSpecifying Protocol Settings Preparation for Protocol SettingsOpen all three one-touch speed dialing panels Specifying Network Settings from the Operation PanelPress or until 6.SYSTEM Settings appears Press SetIf you want to set Dhcp to ‘ON’ or ‘OFF’ If you want to set Bootp to ‘ON’ or ‘OFF’ If you want to set Rarp to ‘ON’ or ‘OFF’To specify the IP address To specify the default gateway To specify the subnet maskEnter the DNS server address using the numeric keys Press or until 5.DNS Server ADD. appearsPress or until 6.DNS Dynamic SET appears Setting the Host Name Setting the Domain Name Data Registration Press Data Registration Press Stop to return to the Standby modePress or until 4.NETWORK Settings appears Open all three one-touch speed dialing panelsPress or until 9.VIEW IP Address appears Using NetSpotPress or to scroll through the settings you want to CheckUsing a Web Browser Remote UI Set up the web browser to accept cookiesSelect Administrator Mode click OK Using a TCP/IP Network Windows/UNIX For LPD Print Specify the LPD settingsSpecify the IP Address, Subnet Mask, and Gateway Address For LPD BannerIf you are using DNS, specify the DNS settings Using ARP/PING Commands Start up the MS-DOS prompt or the Command promptClick OK Using an FTP Client Execute the following commandIf no password has been set Execute the following command to upload the conﬁg ﬁleIf a password has been set for the machine Enter root as the user nameSetting Up a Computer for Printing Connecting to a TCP/IP NetworkPrinter Connection Method LPD/Raw Windows 95/98/MeOpen the printer’s Properties dialog box Specify the Spool settings Specify the port settings Click OK to enable the settings Windows 2000/XPIf you are using Windows If you are using Windows XPAdd Standard TCP/IP Printer Port Wizard starts 30Setting Up a Computer for Printing Click OK to enable the settings Check that Microsoft Windows TCP/IP Printing is installed If necessary, install Microsoft TCP/IP PrintingOpen the printer’s Properties dialog box 34Setting Up a Computer for Printing Example using Solaris UnixExample using Red Hat Linux Example using TurbolinuxExample using HP-UX Example using IBM-AIX Printer Connection Method IPPStart the Add Printer Wizard Enter the URL of your printerPrinter location settings are complete Print Server Settings From the printer’s pop-up menu, display the Sharing sheetSpecify the Sharing settings Using the Remote UI Printer ManagementOperation Command 44Printer Management Using a NetWare Network Windows NetWare Network Setup Procedures See NetWare Print Service Settings, on pNetWare Print Service Settings Print ServicesNDS Novell Directory Service and Bindery Mode Specifying Print Service Settings Using NetSpot Setup Using NetWare Administrator or PconsoleQueue Server Mode and Remote Printer Mode Specify the Print Server name, Printer, and Queue settings Enter the print server name in Print Server nameSet up a queue assign the print server to the queue Assign the printer to the print server Specify the printer name, type, and any remaining itemsAssign a queue to the printer 8NetWare Print Service Settings Protocol Settings 10Protocol Settings Printer’s Location Setting Connecting to a NetWare NetworkInstalling the Printer Driver Specify the printer’s location12Setting Up a Computer for Printing Using a NetBIOS Network Windows 95/98/Me NetBIOS Network Setup Procedures Connecting to a NetBIOS Network To set up the printer’s location, follow the procedure below Specify the Spool settings 6Setting Up a Computer for Printing Click OK to enable the settings 8Setting Up a Computer for Printing Appendix Troubleshooting GuideTroubleshooting 4Troubleshooting How to Uninstall Software LPR Port Utility DeletionNetBIOS/NetBEUI Port Monitor Utility Deletion Click YesUsing NetSpot, Remote UI, or FTP Client Overview of Network Setting ItemsUsing the Operation Panel System SettingsCommon Settings Setting Description DefaultTCP/IP Settings TcpframetypeTcpprtcontlist NetWare Settings NcpburstmodeNetBIOS Settings Available Software for Network Settings FTPBuffer size GlossaryBanding Container objectDNS server Domain CookieDaemon Ethernet Gateway Address Internet Protocol IP IP address NetBIOS NCP Burst ModeNDS Novell Directory Services Log onProtocol Queue Server modePacket Signature Proxy serverScope ID Switching hubRIP Raster Image Processor Snmp Simple Network Management ProtocolVector Graphics WANIndex Index Nwadmin Appendix 120V

Related manuals

Manual 358 pages 5.87 Kb

Manual 6 pages 32 Kb