Avery 676 user manual Printer Unpacking / Installation, AC Power Line

Page 15

AC Power Line

AVERY DENNISON requires that the electric service be 10 Amps @ 115VAC or 10 Amps @ 230VAC. This will allow the computer and any additional support or service equipment to be plugged into the same service.

Any electrical service which is supplying a AVERY DENNISON printer or peripheral equipment connected to a AVERY DENNISON printer should follow standard electrical code practices including proper grounding and neutral requirements.

The AVERY DENNISON printer was designed to operate in an industrial setting for extended periods of time; however, the printer is controlled by a microprocessor which is very sensitive to brownouts or power spikes. For this reason as well as the minimum recommended current supply, AVERY DENNISON recommends that a separate “clean” service be installed or reserved for the exclusive use of the AVERY DENNISON printer and it’s peripherals.

Printer Unpacking / Installation

Unpacking

The AVERY DENNISON printer is shipped in a large cardboard box that may be difficult to move by hand.

DO NOT REMOVE THE PRINTER FROM THE PACKAGE OR UNPACK

IN THE SHIPPING / RECEIVING DEPARTMENT.

NOTE: Unpacking in the shipping / receiving department is not recommended for the following reasons.

First: The box in which your AVERY DENNISON printer was shipped allows the printer to be moved with a forklift, forkcart or handcart. Because of the weight of the printer, it is easier and safer to use one of these devices to move the printer to its intended installation location.

Second: Leaving the printer in the crate while it is being moved within your facility will help to protect the printer during the movements to this new location. Once the printer has reached its intended location you should begin the unpacking process.

Open the box from top by removing the two (2) banding straps and cutting the tape seam on top of the printer. (See Figure 3).

Remove the plastic over the printer.

Remove all the smaller loss items from in and around the printer.

There is a sleeve to lift the printer from the box for easy removal.

Lift the printer onto the table.

User Manual Model 676 LOKPRINT®

Printer Unpacking / Installation 9

Image 15
Contents Manual Edition August Model 676 LokprintThis page intentionally blank Contents Adjustments Scope Page Safety Issues / Warnings ScopeIntroduction Parts Warranty InformationLimited Warranty ServicePrinter Description Description / SpecificationsDescription / Specifications Printer Specification Personal Computer Specifications Location of Printer Customer ResponsibilityCustomer Responsibility Printer Unpacking / Installation AC Power LineUnpacking Avery Dennison 676LKP Tool KIT #371391 Inventory of ComponentsFuses must be between points a and B as shown not B and C Fuse ConfigurationTCB Dip Switch S2 Settings Installing the Power CordInstalling the PC Interface Cable Installing the PC SoftwareLoading Stock Printer OperationWeb Guides Butt SpliceANTI-STATIC Gloves and the ANTI-STATIC Wrist Strap Print Head OperationPrint Head Open / Closed Installing Ink Ribbon Splices Feed Control Panel OperationPrinter Controls StartOn Line Indicator LightsTest StopSensor ErrorHome Screen Display ModesSetup Screen Verifier Setup Screen Power UP Diagnostics Home Screen Print / CUT Positions Printhead Setup Control Panel Operation Printhead Setup Feature Setup Screen Control Panel Operation Control Panel Operation Sensors AdjustmentsSensor Adjustments Feed Roller PressureMachine Set Up Sequence Procedure MaintenanceCleaning Print Head CleaningClean Platen Roller Print Head HandlingHandling Print Head Replacement Remove the old printhead carefully from the heat sink Printhead Category Chart Composition Iglide Bearings Lubrication ProcedurePower Up / Sign On / Communications Electrical Trouble ShootingProblem Probable Cause Corrective Action Stock / Ink Advance Print Stock Mechanical Trouble ShootingInk Appendix a Error MessagesSoftware Upgrade Chip Placement Positions Appendix BThermal Control Board P/N 371105TT Head Driver Board Head Driver Board P/N 371106TTFront Panel Board P / N Front Panel Diagnostic DescriptionsAppendix C Printhead Life ExtensionMatching stock and ink widths Printhead Fail Modes Symptoms, Causes, SolutionsPrinthead Cleaning Procedure Machine Cleaning ProcedurePrinthead cleaning when removed from the printer Printhead Installation and Removal Procedures Printhead removal procedurePrinthead installation procedure Machine Wiring Electrical Assembly DrawingsElectrical System Schematic Motherboard Power Connectors Mechanical Assembly Drawings Unwind Assembly Drawing Unwind Parts List Web Guide Assembly Drawing Web Guide Parts List Drive Assembly Drawing Drive Parts List Top Printhead Assembly Drawing Top Printhead Parts List Bottom Printhead Assembly Drawing Bottom Printhead Parts List Ink Unwind / Rewind Assembly Drawing Ink Unwind / Rewind Parts List Web Tension Guide Assembly Drawing Web Tension Guide Parts List Drive Belt Routing Drawing Mechanical Assembly Drawings