Avery 676 user manual Installing Ink Ribbon

Page 23

Installing Ink Ribbon

The ink ribbon comes pre-packaged in a plastic bag. For best results, leave the ink ribbon wrapped in this bag until you are ready to use it in the printer. Use the procedure and diagram below for loading the ink.

SUPPLY

TAKE-UP

SUPPLY

TAKE-UP

HEAD 2

HEAD 3

HEAD 2

HEAD 3

 

 

FABRIC

INK

WEB GUIDE

HEAD 2

HEAD 3

 

 

HEAD 1

DRIVE / AUX

STOCK

TAKE-UP

HEAD 1

SUPPLY

HEAD 1

INK

Figure 6

1)Unwrap the ink ribbon and put it on the ink-ribbon supply arbor for the print station to be loaded (Figure 6) by pressing it on to the arbor when the three slots are lined up.

2)Make sure the ink ribbon comes off the roll in the direction shown and is threaded as illustrated (Figure 6).

NOTE: A new ink ribbon has a leader that makes it easier to use when threading the ribbon through the print area.

3)Place an empty ink-ribbon take-up core on the ink-ribbon take-up arbor for the print station to be loaded. The ink take-up core must be at least as wide as the ink supply.

4)Open the print head to the print station being loaded.

5)After starting the leader off the supply roll - pull enough ink off to thread though the print station and onto the take up core. The adhesive on the supply roll of ink will be used to fasten the leader to the take up core.

NOTE: Make sure that the ink-ribbon take-up core and the ink-ribbon supply roll are both against the ink backer plate so that the ink ribbon tracks straight through the print station.

User Manual Model 676 LOKPRINT®

Printer Operation 17

Image 23
Contents Manual Edition August Model 676 LokprintThis page intentionally blank Contents Adjustments Scope Page Introduction Safety Issues / WarningsScope Parts Warranty InformationLimited Warranty ServicePrinter Description Description / SpecificationsDescription / Specifications Printer Specification Personal Computer Specifications Location of Printer Customer ResponsibilityCustomer Responsibility Unpacking Printer Unpacking / InstallationAC Power Line Avery Dennison 676LKP Tool KIT #371391 Inventory of ComponentsFuses must be between points a and B as shown not B and C Fuse ConfigurationTCB Dip Switch S2 Settings Installing the Power CordInstalling the PC Interface Cable Installing the PC SoftwareLoading Stock Printer OperationWeb Guides Butt SpliceANTI-STATIC Gloves and the ANTI-STATIC Wrist Strap Print Head OperationPrint Head Open / Closed Installing Ink Ribbon Splices Feed Control Panel OperationPrinter Controls StartOn Line Indicator LightsTest StopSensor ErrorHome Screen Display ModesSetup Screen Verifier Setup Screen Power UP Diagnostics Home Screen Print / CUT Positions Printhead Setup Control Panel Operation Printhead Setup Feature Setup Screen Control Panel Operation Control Panel Operation Sensors AdjustmentsSensor Adjustments Feed Roller PressureMachine Set Up Sequence Procedure MaintenanceCleaning Print Head CleaningHandling Clean Platen RollerPrint Head Handling Print Head Replacement Remove the old printhead carefully from the heat sink Printhead Category Chart Composition Iglide Bearings Lubrication ProcedurePower Up / Sign On / Communications Electrical Trouble ShootingProblem Probable Cause Corrective Action Stock / Ink Advance Print Stock Mechanical Trouble ShootingInk Appendix a Error MessagesThermal Control Board P/N 371105TT Software Upgrade Chip Placement PositionsAppendix B Head Driver Board Head Driver Board P/N 371106TTFront Panel Board P / N Front Panel Diagnostic DescriptionsMatching stock and ink widths Appendix CPrinthead Life Extension Printhead Fail Modes Symptoms, Causes, SolutionsPrinthead cleaning when removed from the printer Printhead Cleaning ProcedureMachine Cleaning Procedure Printhead installation procedure Printhead Installation and Removal ProceduresPrinthead removal procedure Machine Wiring Electrical Assembly DrawingsElectrical System Schematic Motherboard Power Connectors Mechanical Assembly Drawings Unwind Assembly Drawing Unwind Parts List Web Guide Assembly Drawing Web Guide Parts List Drive Assembly Drawing Drive Parts List Top Printhead Assembly Drawing Top Printhead Parts List Bottom Printhead Assembly Drawing Bottom Printhead Parts List Ink Unwind / Rewind Assembly Drawing Ink Unwind / Rewind Parts List Web Tension Guide Assembly Drawing Web Tension Guide Parts List Drive Belt Routing Drawing Mechanical Assembly Drawings