Toshiba B-680-QQ, B-670-QQ owner manual Media, Ribbon

2. SPECIFICATIONS

EO1-33015

2.3 MEDIA

2.3	MEDIA
				Label
	Stop	I
	position
	Cut
	position
		J		Reference
			H	coordinate	1
				Reference
				coordinate	2
				G
				D

Refer to the following
NOTE 2.
Black Mark	Tag paper	Black Mark
(on reverse side)	I	(on reverse side)
Stop		Tag paper
position
E		F
Cut
position

	Reference
A	coordinate 1	A
B	H
	Reference
	coordinate	2

Feed direction

G

C

Fig. 2-1

C

[Unit: mm]

		Label dispensing mode		Batch mode	Strip mode		Cut mode
Item
			B-672	10.00 ~ 999.0	25.4	~ 999.0	Label: 38 ~ 999.0
A : Span of one label/tag							Tag: 25.4 ~ 999.0
			B-682	10.00 ~ 1709.0	25.4 ~ 1709.0		Label: 38 ~ 1709.0
							Tag: 25.4 ~ 1709.0
B : Label length			B-672	7.5 ~ 996.5	22.9	~ 996.5	25.0 ~ 993.0
			B-682	7.5 ~ 1707.0	22.9 ~ 1707.0		25.0 ~ 1703.0
C : Width including backing paper				84.0 ~ 175.0 (See NOTE 3.)
D : Label width					81.0 ~ 172.0
E : Gap length				2.5 ~ 20.0	2.5	~ 20.0	6.0 ~ 20.0
F : Black mark length (Tag paper)					2.5	~ 10.0
G : Effective print width					10.0	~ 170.6
H :		Standard	B-672	5.5 ~ 298.6	20.9	~ 298.6	23.0 ~ 298.6
	Label		B-682	5.5 ~ 1705.0	20.9 ~ 1705.0		23.0 ~ 1705.0
Effective		Max. memory	B-672	5.5 ~ 981.3	20.9	~ 981.3	23.0 ~ 981.3
print length		Standard	B-672	8.0 ~ 298.6	23.4	~ 298.6	23.4 ~ 298.6
	Tag		B-682	8.0 ~ 1705.0			23.4 ~ 1705.0
		Max. memory	B-672	8.0 ~ 981.3	23.4	~ 981.3	23.4 ~ 981.3
I : Print speed up/slow down area						1.0
J : Black mark length (Label)				Refer to the following NOTE 2.
Maximum effective		Standard	B-672		149.3
length for on the fly			B-682		852.0
isue
		Max. memory	B-672		490.6
Outer roll diameter					Ø200 Max.
Thickness	Label				0.13 ~ 0.17
	Tag				0.10 ~ 0.17

NOTES:

1.The media specification other than above are unchanged.

2.When marking black marks on label rolls, the following requirements must be satisfied. When the gap length is less than 4 mm:

The black mark length should be longer than the gap length. When the gap length is 4 mm or more:

The black mark should not overlap the gap for more than 4 mm and the following label.

3.When the print speed is 8"/sec., the width including backing paper will be 84 to 150 mm. When the optional cutter module or strip module is used, the width including backing paper will be 101.6 to 175 mm.

4.If the label used is smaller than specified, the print head life may be shortened.

5.When issuing thermal labels at 8"/sec., the print stop position should be set to a minimum of 1 mm inside the label.

2.4 RIBBON

Type	Spool type
Width	115 mm ~ 185 mm
	(See NOTE 5.)
Length	300 m
Outer diameter	Ø72 mm (max.)

NOTES:

1.“On the fly issue” means that the printer can draw and print without stopping between labels.

2.To ensure print quality and print head life use only TOSHIBA TEC specified media and ribbons.

3.When using the cutter ensure that label length B plus inter label gap length E exceeds 35 mm. (i.e. label pitch should be greater than 35 mm.)

4.To avoid ribbon wrinkles use the ribbon which is wider than media by 5mm or more. However, too much difference in width between the two may cause wrinkles.

5.When the print speed is 8"/sec., the width will be 115 to 160 mm.

2-3