Toshiba e-STUDIO203 manual If the Function Clear lamp is blinking and copying stops

Page 67

1 Place paper in the drawer.

2 Press the [COPY] button several times until the lamp of the desired paper size is lit.

e.g.) Selecting A4 size

You can select the desired paper size with the [DRAWER] button in the same procedure.

3

4

Press the APS/AMS selecting button until the AMS lamp is lit.

Place the original on the Automatic Document Feeder (optional).

The equipment detects the size of the original, and then the most suitable reproduction ratio to the copy paper size is set.

5 Select the other copy modes as required, and then press the [START] button.

If the [FUNCTION CLEAR] lamp is blinking and copying stops

The direction of the original placed is not correct. Press the [FUNCTION CLEAR] button to exit the original. Then rotate the original by 90 degrees to place it in the correct direction.

Zooming In/Out Copy Image 65

Image 67

Contents Operators Manual for Copying Functions EPA Energy Star MFD For Germany only For EU onlyPage Operator’s Manual for Copying Functions Lineup of Our ManualsBefore Reading This Manual Precautions in this manualTrademarks Description of original/paper directionBefore Reading This Manual Contents 100 Copying in Same Page Order as Originals Sort CopyingIndex 111Contents Toner remaining check function Toshiba Quality is Second to NoneRecommended toner cartridges Cartridge detecting functionToner Supplies / PartsGeneral Functions extended by various options Features of e-STUDIO163/203Ecological energy-saving design When installing or moving General Precautions10 cm 80 cm Other pointsWhen using the equipment Position of Certification label, etc When handling supplies During maintenance or inspectionPoration Disclaimer NoticeDisclaimer Notice Description of Each Component Preparation 1 Turning Power onPreparation 2 Placing Copy Paper Automatic Document Feeder optional, MR-2017 Description of Each ComponentFront / Right side Platen CoverLeft side / Inner side Platen sheet USB terminal 4-pinReceiving tray Scanning area Original scaleConfiguration of options Control panel Copy qty. / zoom display selecting button/lamp Original mode button/lampsDensity adjustment buttons/lamps LED displayOriginal button/lamps Original setting lampDrawer button/lamps Copy button/lampsTurning power on Preparation 1 Turning Power onTurning power OFF To turn the equipment into the energy saving mode manually Saving energy when not in use Energy saving modeCancelling the energy saving mode Acceptable media types Preparation 2 Placing Copy PaperFeeder Media type Paper size Maximum sheet Capacity *1 Media type Product name Recommended paperPaper types not acceptable Storing paperPress down the paper plate Placing paper in drawersWiden the gap with both hands Place paper in the drawer Adjust the side guides to the desired paper sizeRegister the paper size into the equipment Do not let your fingers be caught when closing the drawerRegistering standard size A3, A4, A4-R, A5-R, B4 Preparation 3 Registering Size of Paper PlacedCode No Registering other standard sizesPreparation 3 Registering Size of Paper Placed Press the Start button Placing Originals Using Bypass TrayMaking Copies Acceptable originals When the built-in memory has become full during scanningSetting position Type of origi Placing OriginalsPlacing originals on the original glass Placing booklet-type originals such as books or catalogues Maximum number Paper weight Using Automatic Document Feeder optionalPrecautions for Automatic Document Feeder optional When black streaks appear on the copied imagePlacing originals on Automatic Document Feeder optional When placing a large amount of originals with a long widthSelect the copy modes as required Making CopiesCheck if paper is placed in the drawer Place the originalPress the CLEAR/STOP button during scanning or copying When the number of sheets exiting has exceededWhen the paper has run out Stopping/Resuming copyingPress the Interrupt button Interrupting copying and making another copy Interrupt copyMedia type Paper size Maximum sheet Capacity *1 Using Bypass TrayPreparation Registering paper size placed on bypass tray ST-R Folio Comp Using Bypass Tray Press the Start button Bypass copying on standard size paper Placed on the bypass tray is lit Using Bypass Tray Using Bypass Tray Zooming In/Out Copy Image Default Settings Paper SelectionAutomatic paper selection APS Manual paper selection Contents Default setting at installation Default SettingsAutomatic paper selection APS Paper SelectionAutomatic paper selection APS Place the original on the Automatic Document FeederPlace paper in the drawer Place the original Manual paper selectionSelecting the drawer of the equipment Specifying reproduction ratio manually Zooming In/Out Copy ImageAutomatic magnification selection AMS Automatic magnification selection AMSIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Press Zooming out or Specifying reproduction ratio manuallyDesired reproduction ratio appears Zooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Selecting Image Mode Dark Adjusting Density LevelTo adjust the density to the desired level To return it to the automatic copy density modeAdjusting Density Level Settings and Management Equipment All lamps on Sound on All lamps off Sound off Switching Operation Sound On/OffChecking Total Number Copied Switch the display to check the rest of the total numberPress Button for more than two seconds Checking Total Number Copied When Message Lamp is Lit/Blinking Paper Jams TroubleshootingToner lamp When Message Lamp is Lit/BlinkingCover open lamp Paper empty lampRecommended toner cartridges Paper jam lamp Service call lampPaper Jams When paper jams occur frequentlyChecking position of paper jams Do not tear jammed paper When releasing jammed paperPaper jams within Automatic Document Feeder optional Raise the lever, and then open the upper coverPaper Jams Pull out the paper jammed on the bypass tray Paper jams on bypass trayPaper jam behind transfer unit Close the transfer unit and the side cover Open the transport guide while holding the knob a Paper jams within fuser unitRelease the jammed paper Paper jams within Paper Feed Unit optional Open the front cover Replacing Toner CartridgeHold down the green lever Pull out the toner cartridge Insert the toner cartridge along the rail Clean the chargerOpen the side cover With the transfer charger wire Equipment starts supplying toner General operation Before Calling Service TechnicianPhenomenon Usual cause Countermeasure Original/Copy paper-related items Toner-related itemsImage trouble Tion Charger is dirty Clean the charger Daily Inspection 100 Maintenance and InspectionOriginal glass Guides Platen sheet Daily InspectionOpen the front cover Clean the charger Cleaning chargerCleaning transfer charger Daily Inspection Daily Inspection Specifications and Options OPC STUDIO163/203 SpecificationsPaper size Feeder STUDIO163 STUDIO203 Continuous copying speedAutomatic Document Feeder Specifications of OptionsPaper Feed Unit Packing List Packing List AMS APS Index106 DP-1640/2030 OME050129B0 Multifunctional Digital Systems