Toshiba e-STUDIO203 manual Preparation 3 Registering Size of Paper Placed

Page 39

Preparation 3 - Registering Size of Paper Placed

When you place paper in a drawer for the first time or when you place paper whose size is differ- ent from that of the paper which has been placed in the drawer, the new paper size needs to be registered into the equipment.

Registration of standard sizes (A3, A4, A4-R, A5-R, B4) differs from that of standard sizes other than these.

Registering standard size (A3, A4, A4-R, A5-R, B4)

In this section, A4 size is registered in the drawer of the equipment as an example.

1 Press and hold the [COPY] and [DRAWER] buttons simultaneously for more than two seconds.

“Fnc” appears on the LED display.

2 Press the [DRAWER] button several times until the lamp of the drawer in which you placed paper is lit.

Preparation 3 - Registering Size of Paper Placed 37

Image 39

Contents Operators Manual for Copying Functions EPA Energy Star MFD For Germany only For EU onlyPage Operator’s Manual for Copying Functions Lineup of Our ManualsBefore Reading This Manual Precautions in this manualTrademarks Description of original/paper directionBefore Reading This Manual Contents 100 Copying in Same Page Order as Originals Sort CopyingIndex 111Contents Toner remaining check function Toshiba Quality is Second to NoneRecommended toner cartridges Cartridge detecting functionSupplies / Parts TonerGeneral Features of e-STUDIO163/203 Functions extended by various optionsEcological energy-saving design When installing or moving General Precautions10 cm 80 cm Other pointsWhen using the equipment Position of Certification label, etc When handling supplies During maintenance or inspectionPoration Disclaimer NoticeDisclaimer Notice Preparation 1 Turning Power on Description of Each ComponentPreparation 2 Placing Copy Paper Automatic Document Feeder optional, MR-2017 Description of Each ComponentFront / Right side Platen CoverLeft side / Inner side Platen sheet USB terminal 4-pinReceiving tray Scanning area Original scaleConfiguration of options Control panel Copy qty. / zoom display selecting button/lamp Original mode button/lampsDensity adjustment buttons/lamps LED displayOriginal button/lamps Original setting lampDrawer button/lamps Copy button/lampsPreparation 1 Turning Power on Turning power onTurning power OFF Saving energy when not in use Energy saving mode To turn the equipment into the energy saving mode manuallyCancelling the energy saving mode Preparation 2 Placing Copy Paper Acceptable media typesFeeder Media type Paper size Maximum sheet Capacity *1 Media type Product name Recommended paperPaper types not acceptable Storing paperPress down the paper plate Placing paper in drawersWiden the gap with both hands Place paper in the drawer Adjust the side guides to the desired paper sizeRegister the paper size into the equipment Do not let your fingers be caught when closing the drawerRegistering standard size A3, A4, A4-R, A5-R, B4 Preparation 3 Registering Size of Paper PlacedCode No Registering other standard sizesPreparation 3 Registering Size of Paper Placed Press the Start button Using Bypass Tray Placing OriginalsMaking Copies Acceptable originals When the built-in memory has become full during scanningSetting position Type of origi Placing OriginalsPlacing originals on the original glass Placing booklet-type originals such as books or catalogues Maximum number Paper weight Using Automatic Document Feeder optionalPrecautions for Automatic Document Feeder optional When black streaks appear on the copied imagePlacing originals on Automatic Document Feeder optional When placing a large amount of originals with a long widthSelect the copy modes as required Making CopiesCheck if paper is placed in the drawer Place the originalPress the CLEAR/STOP button during scanning or copying When the number of sheets exiting has exceededWhen the paper has run out Stopping/Resuming copyingPress the Interrupt button Interrupting copying and making another copy Interrupt copyMedia type Paper size Maximum sheet Capacity *1 Using Bypass TrayPreparation Registering paper size placed on bypass tray ST-R Folio Comp Using Bypass Tray Press the Start button Bypass copying on standard size paper Placed on the bypass tray is lit Using Bypass Tray Using Bypass Tray Default Settings Paper Selection Zooming In/Out Copy ImageAutomatic paper selection APS Manual paper selection Contents Default setting at installation Default SettingsAutomatic paper selection APS Paper SelectionAutomatic paper selection APS Place the original on the Automatic Document FeederPlace paper in the drawer Place the original Manual paper selectionSelecting the drawer of the equipment Specifying reproduction ratio manually Zooming In/Out Copy ImageAutomatic magnification selection AMS Automatic magnification selection AMSIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Specifying reproduction ratio manually Press Zooming out orDesired reproduction ratio appears Zooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Selecting Image Mode Dark Adjusting Density LevelTo adjust the density to the desired level To return it to the automatic copy density modeAdjusting Density Level Settings and Management Equipment All lamps on Sound on All lamps off Sound off Switching Operation Sound On/OffSwitch the display to check the rest of the total number Checking Total Number CopiedPress Button for more than two seconds Checking Total Number Copied When Message Lamp is Lit/Blinking Paper Jams TroubleshootingToner lamp When Message Lamp is Lit/BlinkingCover open lamp Paper empty lampRecommended toner cartridges Paper jam lamp Service call lampWhen paper jams occur frequently Paper JamsChecking position of paper jams Do not tear jammed paper When releasing jammed paperPaper jams within Automatic Document Feeder optional Raise the lever, and then open the upper coverPaper Jams Pull out the paper jammed on the bypass tray Paper jams on bypass trayPaper jam behind transfer unit Close the transfer unit and the side cover Open the transport guide while holding the knob a Paper jams within fuser unitRelease the jammed paper Paper jams within Paper Feed Unit optional Replacing Toner Cartridge Open the front coverHold down the green lever Pull out the toner cartridge Clean the charger Insert the toner cartridge along the railOpen the side cover With the transfer charger wire Equipment starts supplying toner Before Calling Service Technician General operationPhenomenon Usual cause Countermeasure Original/Copy paper-related items Toner-related itemsImage trouble Tion Charger is dirty Clean the charger Daily Inspection 100 Maintenance and InspectionOriginal glass Guides Platen sheet Daily InspectionOpen the front cover Clean the charger Cleaning chargerCleaning transfer charger Daily Inspection Daily Inspection Specifications and Options OPC STUDIO163/203 SpecificationsPaper size Feeder STUDIO163 STUDIO203 Continuous copying speedSpecifications of Options Automatic Document FeederPaper Feed Unit Packing List Packing List AMS APS Index106 DP-1640/2030 OME050129B0 Multifunctional Digital Systems