Toshiba e-STUDIO203 manual Using Bypass Tray

Page 59

5 Select the other copy modes as required, and then press the [START] button.

Copying starts.

When you make copies on overhead transparencies using the bypass tray, pick up the transparencies which have exited onto the receiving tray one by one. If the transparen- cies pile up, they may become curled and not be good for projection.

yWhen the paper on the bypass tray has run out during copying, copying continues with the paper of the same size in the drawer as the one on the bypass tray. (If the size of the paper on the bypass tray has not been registered in advance, however, copying stops. In this case, add paper to the bypass tray and press the [START] but- ton to resume copying.)

yWhen bypass copying has finished, the [FUNCTION CLEAR] lamp blinks. Press the [FUNCTION CLEAR] button so that the paper size setting for the bypass tray will be cleared. Press the [FUNCTION CLEAR] button again so that bypass copying will be switched to copying with drawer feeding.

Using Bypass Tray 57

Image 59

Contents Operators Manual for Copying Functions EPA Energy Star MFD For Germany only For EU onlyPage Operator’s Manual for Copying Functions Lineup of Our ManualsBefore Reading This Manual Precautions in this manualTrademarks Description of original/paper directionBefore Reading This Manual Contents 100 Copying in Same Page Order as Originals Sort CopyingIndex 111Contents Toner remaining check function Toshiba Quality is Second to NoneRecommended toner cartridges Cartridge detecting functionGeneral Supplies / PartsToner Ecological energy-saving design Features of e-STUDIO163/203Functions extended by various options When installing or moving General Precautions10 cm 80 cm Other pointsWhen using the equipment Position of Certification label, etc When handling supplies During maintenance or inspectionPoration Disclaimer NoticeDisclaimer Notice Preparation 2 Placing Copy Paper Preparation 1 Turning Power onDescription of Each Component Automatic Document Feeder optional, MR-2017 Description of Each ComponentFront / Right side Platen CoverLeft side / Inner side Platen sheet USB terminal 4-pinReceiving tray Scanning area Original scaleConfiguration of options Control panel Copy qty. / zoom display selecting button/lamp Original mode button/lampsDensity adjustment buttons/lamps LED displayOriginal button/lamps Original setting lampDrawer button/lamps Copy button/lampsTurning power OFF Preparation 1 Turning Power onTurning power on Cancelling the energy saving mode Saving energy when not in use Energy saving modeTo turn the equipment into the energy saving mode manually Feeder Media type Paper size Maximum sheet Capacity *1 Preparation 2 Placing Copy PaperAcceptable media types Media type Product name Recommended paperPaper types not acceptable Storing paperPress down the paper plate Placing paper in drawersWiden the gap with both hands Place paper in the drawer Adjust the side guides to the desired paper sizeRegister the paper size into the equipment Do not let your fingers be caught when closing the drawerRegistering standard size A3, A4, A4-R, A5-R, B4 Preparation 3 Registering Size of Paper PlacedCode No Registering other standard sizesPreparation 3 Registering Size of Paper Placed Press the Start button Making Copies Using Bypass TrayPlacing Originals Acceptable originals When the built-in memory has become full during scanningSetting position Type of origi Placing OriginalsPlacing originals on the original glass Placing booklet-type originals such as books or catalogues Maximum number Paper weight Using Automatic Document Feeder optionalPrecautions for Automatic Document Feeder optional When black streaks appear on the copied imagePlacing originals on Automatic Document Feeder optional When placing a large amount of originals with a long widthSelect the copy modes as required Making CopiesCheck if paper is placed in the drawer Place the originalPress the CLEAR/STOP button during scanning or copying When the number of sheets exiting has exceededWhen the paper has run out Stopping/Resuming copyingPress the Interrupt button Interrupting copying and making another copy Interrupt copyMedia type Paper size Maximum sheet Capacity *1 Using Bypass TrayPreparation Registering paper size placed on bypass tray ST-R Folio Comp Using Bypass Tray Press the Start button Bypass copying on standard size paper Placed on the bypass tray is lit Using Bypass Tray Using Bypass Tray Automatic paper selection APS Manual paper selection Default Settings Paper SelectionZooming In/Out Copy Image Contents Default setting at installation Default SettingsAutomatic paper selection APS Paper SelectionAutomatic paper selection APS Place the original on the Automatic Document FeederPlace paper in the drawer Place the original Manual paper selectionSelecting the drawer of the equipment Specifying reproduction ratio manually Zooming In/Out Copy ImageAutomatic magnification selection AMS Automatic magnification selection AMSIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Desired reproduction ratio appears Specifying reproduction ratio manuallyPress Zooming out or Zooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Selecting Image Mode Dark Adjusting Density LevelTo adjust the density to the desired level To return it to the automatic copy density modeAdjusting Density Level Settings and Management Equipment All lamps on Sound on All lamps off Sound off Switching Operation Sound On/OffPress Button for more than two seconds Switch the display to check the rest of the total numberChecking Total Number Copied Checking Total Number Copied When Message Lamp is Lit/Blinking Paper Jams TroubleshootingToner lamp When Message Lamp is Lit/BlinkingCover open lamp Paper empty lampRecommended toner cartridges Paper jam lamp Service call lampChecking position of paper jams When paper jams occur frequentlyPaper Jams Do not tear jammed paper When releasing jammed paperPaper jams within Automatic Document Feeder optional Raise the lever, and then open the upper coverPaper Jams Pull out the paper jammed on the bypass tray Paper jams on bypass trayPaper jam behind transfer unit Close the transfer unit and the side cover Open the transport guide while holding the knob a Paper jams within fuser unitRelease the jammed paper Paper jams within Paper Feed Unit optional Hold down the green lever Replacing Toner CartridgeOpen the front cover Pull out the toner cartridge Open the side cover Clean the chargerInsert the toner cartridge along the rail With the transfer charger wire Equipment starts supplying toner Phenomenon Usual cause Countermeasure Before Calling Service TechnicianGeneral operation Original/Copy paper-related items Toner-related itemsImage trouble Tion Charger is dirty Clean the charger Daily Inspection 100 Maintenance and InspectionOriginal glass Guides Platen sheet Daily InspectionOpen the front cover Clean the charger Cleaning chargerCleaning transfer charger Daily Inspection Daily Inspection Specifications and Options OPC STUDIO163/203 SpecificationsPaper size Feeder STUDIO163 STUDIO203 Continuous copying speedPaper Feed Unit Specifications of OptionsAutomatic Document Feeder Packing List Packing List AMS APS Index106 DP-1640/2030 OME050129B0 Multifunctional Digital Systems