Toshiba e-STUDIO203 manual Toner-related items, Original/Copy paper-related items

Page 98

5 TROUBLESHOOTING

Toner-related items

Phenomenon

Usual cause

Countermeasure

The toner lamp is lit.

There is only a little toners

This is not an equipment malfunction.

 

remaining in the toner car-

(There is still some toner in the toner car-

 

tridge.

tridge. Do not replace the toner cartridge

 

 

until the toner lamp starts blinking.)

 

The toner cartridge is not

Install the toner cartridge correctly.

 

installed. Or it is not installed

 

 

correctly.

 

 

A toner cartridge not recom-

Use a TOSHIBA-recommended toner car-

 

mended by TOSHIBA is

tridge. If you use a toner cartridge other

 

being used.

than the one we recommend and you feel

 

 

annoyed by this lighting lamp, contact

 

 

your service representative.

 

 

P.11 “Recommended toner cartridges”

The toner lamp is blinking.

The toner in the toner

Replace the toner cartridge with a new

 

cartridge has run out.

one.

The toner lamp does not light

The toner-remaining check

Contact your service representative.

even when the toner has

function has been disabled

 

almost run out.

since the purchase of the

 

 

equipment.

 

The equipment does not

The toner cartridge inserted

Check the product name of the toner car-

become ready for copying

is not usable for this equip-

tridge. If you can see “T-1640”, this car-

after the toner cartridge is

ment.

tridge is usable.

inserted.

 

 

Original/Copy paper-related items

Phenomenon

Usual cause

Countermeasure

An original jams.

An original not acceptable for

Check if the original is acceptable for the

 

the equipment is being used.

equipment.

 

 

P.45 “Precautions for Automatic Docu-

 

 

ment Feeder (optional)”

Copy paper jams.

Copy paper not acceptable

Check if the copy paper is acceptable for

 

for the equipment is being

the equipment.

 

used.

P.32 “Paper types not acceptable”

 

The size of the copy paper in

Register the size of the placed copy paper

 

the drawer or on the bypass

properly.

 

tray is not registered prop-

P.37 “Preparation 3 - Registering Size

 

erly in the equipment.

of Paper Placed”

 

 

P.51 “Preparation - Registering paper

 

 

size placed on bypass tray”

 

Jammed paper is located in

Use the paper jam position lamp to

 

a place you cannot see eas-

recheck the position where the paper jam

 

ily.

has occurred.

 

 

P.81 “Paper Jams”

 

There is no gap between the

Adjust the gap between the side guides

 

side guides and paper in the

and the paper properly.

 

drawer. Or the gap is too

P.33 “Placing paper in drawers”

 

wide.

 

Multiple feeding occurs.

Paper is clinging to each

Fan the paper well and place it again.

 

other.

 

96 Before Calling Service Technician

Page 97 Page 99
Image 98
Page 97 Page 99
Contents Operators Manual for Copying Functions EPA Energy Star MFD For EU only For Germany onlyPage Lineup of Our Manuals Operator’s Manual for Copying FunctionsPrecautions in this manual Before Reading This ManualDescription of original/paper direction TrademarksBefore Reading This Manual Contents Copying in Same Page Order as Originals Sort Copying 100111 IndexContents Cartridge detecting function Toshiba Quality is Second to NoneRecommended toner cartridges Toner remaining check functionGeneral Supplies / PartsToner Ecological energy-saving design Features of e-STUDIO163/203Functions extended by various options General Precautions When installing or movingOther points 10 cm 80 cmWhen using the equipment Position of Certification label, etc During maintenance or inspection When handling suppliesDisclaimer Notice PorationDisclaimer Notice Preparation 2 Placing Copy Paper Preparation 1 Turning Power onDescription of Each Component Platen Cover Description of Each ComponentFront / Right side Automatic Document Feeder optional, MR-2017Left side / Inner side Original scale USB terminal 4-pinReceiving tray Scanning area Platen sheetConfiguration of options Control panel LED display Original mode button/lampsDensity adjustment buttons/lamps Copy qty. / zoom display selecting button/lampCopy button/lamps Original setting lampDrawer button/lamps Original button/lampsTurning power OFF Preparation 1 Turning Power onTurning power on Cancelling the energy saving mode Saving energy when not in use Energy saving modeTo turn the equipment into the energy saving mode manually Feeder Media type Paper size Maximum sheet Capacity *1 Preparation 2 Placing Copy PaperAcceptable media types Storing paper Recommended paperPaper types not acceptable Media type Product namePlacing paper in drawers Press down the paper plateWiden the gap with both hands Adjust the side guides to the desired paper size Place paper in the drawerDo not let your fingers be caught when closing the drawer Register the paper size into the equipmentPreparation 3 Registering Size of Paper Placed Registering standard size A3, A4, A4-R, A5-R, B4Registering other standard sizes Code NoPreparation 3 Registering Size of Paper Placed Press the Start button Making Copies Using Bypass TrayPlacing Originals Placing Originals When the built-in memory has become full during scanningSetting position Type of origi Acceptable originalsPlacing originals on the original glass Placing booklet-type originals such as books or catalogues When black streaks appear on the copied image Using Automatic Document Feeder optionalPrecautions for Automatic Document Feeder optional Maximum number Paper weightWhen placing a large amount of originals with a long width Placing originals on Automatic Document Feeder optionalPlace the original Making CopiesCheck if paper is placed in the drawer Select the copy modes as requiredStopping/Resuming copying When the number of sheets exiting has exceededWhen the paper has run out Press the CLEAR/STOP button during scanning or copyingInterrupting copying and making another copy Interrupt copy Press the Interrupt buttonUsing Bypass Tray Media type Paper size Maximum sheet Capacity *1Preparation Registering paper size placed on bypass tray ST-R Folio Comp Using Bypass Tray Press the Start button Bypass copying on standard size paper Placed on the bypass tray is lit Using Bypass Tray Using Bypass Tray Automatic paper selection APS Manual paper selection Default Settings Paper SelectionZooming In/Out Copy Image Default Settings Contents Default setting at installationPlace the original on the Automatic Document Feeder Paper SelectionAutomatic paper selection APS Automatic paper selection APSManual paper selection Place paper in the drawer Place the originalSelecting the drawer of the equipment Automatic magnification selection AMS Zooming In/Out Copy ImageAutomatic magnification selection AMS Specifying reproduction ratio manuallyIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Desired reproduction ratio appears Specifying reproduction ratio manuallyPress Zooming out or Zooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Selecting Image Mode To return it to the automatic copy density mode Adjusting Density LevelTo adjust the density to the desired level DarkAdjusting Density Level Settings and Management Equipment Switching Operation Sound On/Off All lamps on Sound on All lamps off Sound offPress Button for more than two seconds Switch the display to check the rest of the total numberChecking Total Number Copied Checking Total Number Copied Troubleshooting When Message Lamp is Lit/Blinking Paper JamsPaper empty lamp When Message Lamp is Lit/BlinkingCover open lamp Toner lampRecommended toner cartridges Service call lamp Paper jam lampChecking position of paper jams When paper jams occur frequentlyPaper Jams Raise the lever, and then open the upper cover When releasing jammed paperPaper jams within Automatic Document Feeder optional Do not tear jammed paperPaper Jams Paper jams on bypass tray Pull out the paper jammed on the bypass trayPaper jam behind transfer unit Close the transfer unit and the side cover Paper jams within fuser unit Open the transport guide while holding the knob aRelease the jammed paper Paper jams within Paper Feed Unit optional Hold down the green lever Replacing Toner CartridgeOpen the front cover Pull out the toner cartridge Open the side cover Clean the chargerInsert the toner cartridge along the rail With the transfer charger wire Equipment starts supplying toner Phenomenon Usual cause Countermeasure Before Calling Service TechnicianGeneral operation Toner-related items Original/Copy paper-related itemsImage trouble Tion Charger is dirty Clean the charger Maintenance and Inspection Daily Inspection 100Daily Inspection Original glass Guides Platen sheetCleaning charger Open the front cover Clean the chargerCleaning transfer charger Daily Inspection Daily Inspection Specifications and Options STUDIO163/203 Specifications OPCContinuous copying speed Paper size Feeder STUDIO163 STUDIO203Paper Feed Unit Specifications of OptionsAutomatic Document Feeder Packing List Packing List Index AMS APS106 DP-1640/2030 OME050129B0 Multifunctional Digital Systems
Top Page Image Contents