Toshiba e-STUDIO203 manual Bypass copying on standard size paper

Page 57

Bypass copying on standard size paper

Standard size paper can be used for bypass copying. In this section, the procedure is described with A4 size thick paper (90 g/m2) placed on the bypass tray as an example.

Register the size of the paper into the equipment in advance.

P.51 “Preparation - Registering paper size placed on bypass tray”

1 Place paper straight on the bypass tray face down. Then align the side guides to the paper length while holding (A).

A

yBe sure that the stack height of paper does not exceed the indicators of the side guides.

yFan the stack of paper well before placing it on the bypass tray.

yDo not push the paper forcibly into the entrance of the bypass feeder. This could cause a paper misfeed.

When you place paper of a larger size, pull out the paper holder before you start bypass copying.

Using Bypass Tray 55

Image 57

Contents Operators Manual for Copying Functions EPA Energy Star MFD For Germany only For EU onlyPage Operator’s Manual for Copying Functions Lineup of Our ManualsBefore Reading This Manual Precautions in this manualTrademarks Description of original/paper directionBefore Reading This Manual Contents 100 Copying in Same Page Order as Originals Sort CopyingIndex 111Contents Recommended toner cartridges Toshiba Quality is Second to NoneCartridge detecting function Toner remaining check functionSupplies / Parts TonerGeneral Features of e-STUDIO163/203 Functions extended by various optionsEcological energy-saving design When installing or moving General Precautions10 cm 80 cm Other pointsWhen using the equipment Position of Certification label, etc When handling supplies During maintenance or inspectionPoration Disclaimer NoticeDisclaimer Notice Preparation 1 Turning Power on Description of Each ComponentPreparation 2 Placing Copy Paper Front / Right side Description of Each ComponentPlaten Cover Automatic Document Feeder optional, MR-2017Left side / Inner side Receiving tray Scanning area USB terminal 4-pinOriginal scale Platen sheetConfiguration of options Control panel Density adjustment buttons/lamps Original mode button/lampsLED display Copy qty. / zoom display selecting button/lampDrawer button/lamps Original setting lampCopy button/lamps Original button/lampsPreparation 1 Turning Power on Turning power onTurning power OFF Saving energy when not in use Energy saving mode To turn the equipment into the energy saving mode manuallyCancelling the energy saving mode Preparation 2 Placing Copy Paper Acceptable media typesFeeder Media type Paper size Maximum sheet Capacity *1 Paper types not acceptable Recommended paperStoring paper Media type Product namePress down the paper plate Placing paper in drawersWiden the gap with both hands Place paper in the drawer Adjust the side guides to the desired paper sizeRegister the paper size into the equipment Do not let your fingers be caught when closing the drawerRegistering standard size A3, A4, A4-R, A5-R, B4 Preparation 3 Registering Size of Paper PlacedCode No Registering other standard sizesPreparation 3 Registering Size of Paper Placed Press the Start button Using Bypass Tray Placing OriginalsMaking Copies Setting position Type of origi When the built-in memory has become full during scanningPlacing Originals Acceptable originalsPlacing originals on the original glass Placing booklet-type originals such as books or catalogues Precautions for Automatic Document Feeder optional Using Automatic Document Feeder optionalWhen black streaks appear on the copied image Maximum number Paper weightPlacing originals on Automatic Document Feeder optional When placing a large amount of originals with a long widthCheck if paper is placed in the drawer Making CopiesPlace the original Select the copy modes as requiredWhen the paper has run out When the number of sheets exiting has exceededStopping/Resuming copying Press the CLEAR/STOP button during scanning or copyingPress the Interrupt button Interrupting copying and making another copy Interrupt copyMedia type Paper size Maximum sheet Capacity *1 Using Bypass TrayPreparation Registering paper size placed on bypass tray ST-R Folio Comp Using Bypass Tray Press the Start button Bypass copying on standard size paper Placed on the bypass tray is lit Using Bypass Tray Using Bypass Tray Default Settings Paper Selection Zooming In/Out Copy ImageAutomatic paper selection APS Manual paper selection Contents Default setting at installation Default SettingsAutomatic paper selection APS Paper SelectionPlace the original on the Automatic Document Feeder Automatic paper selection APSPlace paper in the drawer Place the original Manual paper selectionSelecting the drawer of the equipment Automatic magnification selection AMS Zooming In/Out Copy ImageAutomatic magnification selection AMS Specifying reproduction ratio manuallyIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Specifying reproduction ratio manually Press Zooming out orDesired reproduction ratio appears Zooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Selecting Image Mode To adjust the density to the desired level Adjusting Density LevelTo return it to the automatic copy density mode DarkAdjusting Density Level Settings and Management Equipment All lamps on Sound on All lamps off Sound off Switching Operation Sound On/OffSwitch the display to check the rest of the total number Checking Total Number CopiedPress Button for more than two seconds Checking Total Number Copied When Message Lamp is Lit/Blinking Paper Jams TroubleshootingCover open lamp When Message Lamp is Lit/BlinkingPaper empty lamp Toner lampRecommended toner cartridges Paper jam lamp Service call lampWhen paper jams occur frequently Paper JamsChecking position of paper jams Paper jams within Automatic Document Feeder optional When releasing jammed paperRaise the lever, and then open the upper cover Do not tear jammed paperPaper Jams Pull out the paper jammed on the bypass tray Paper jams on bypass trayPaper jam behind transfer unit Close the transfer unit and the side cover Open the transport guide while holding the knob a Paper jams within fuser unitRelease the jammed paper Paper jams within Paper Feed Unit optional Replacing Toner Cartridge Open the front coverHold down the green lever Pull out the toner cartridge Clean the charger Insert the toner cartridge along the railOpen the side cover With the transfer charger wire Equipment starts supplying toner Before Calling Service Technician General operationPhenomenon Usual cause Countermeasure Original/Copy paper-related items Toner-related itemsImage trouble Tion Charger is dirty Clean the charger Daily Inspection 100 Maintenance and InspectionOriginal glass Guides Platen sheet Daily InspectionOpen the front cover Clean the charger Cleaning chargerCleaning transfer charger Daily Inspection Daily Inspection Specifications and Options OPC STUDIO163/203 SpecificationsPaper size Feeder STUDIO163 STUDIO203 Continuous copying speedSpecifications of Options Automatic Document FeederPaper Feed Unit Packing List Packing List AMS APS Index106 DP-1640/2030 OME050129B0 Multifunctional Digital Systems