Dell Dimension 2100 technical specifications Power, Physical, Environmental, Regulatory Notices

Page 29

Video controller

Intel 810e chip set with Dynamic Video Memory and 4-MB, 133-MHz display cache or Intel

 

810 chip set with Dynamic Video Memory

 

 

Power

DC power supply

Wattage

Heat dissipation

Voltage (switch selectable on back panel)

Backup battery

145 W

700 BTU (fully loaded system without monitor)

90 to 135 V at 60 Hz;

180 to 265 V at 50 Hz;

100 V at 50 to 60 Hz for Japanese systems 3-V CR2032 coin cell

Physical

Height

39 cm (15.375 inches)

Width

16.8 cm (6.625 inches)

Depth

34 cm (13.375 inches)

Weight

9.9 kg (22 lb)

 

 

Environmental

Temperature

 

 

 

Operating

10° to 35°C (50° to 95°F)

3

 

 

 

 

Storage

–40° to 65°C (–40° to 149°F)

 

Relative humidity

20% to 80% (noncondensing)

 

Maximum vibration

 

 

 

Operating

0.25 G at 3 to 200 Hz at 1/2 octave/min

Storage

0.5 G at 3 to 200 Hz at 1/2 octave/min

Maximum shock

 

 

 

Operating

bottom half-sine pulse with a change in velocity of 50.8 cm/sec (20 inches/sec)

Storage

27-G faired-square wave with a velocity change of 508 cm/sec (200 inches/sec)

Altitude

 

 

 

Operating

–15.2 to 3048 m (–50 to 10,000 ft)

3

 

 

Storage

–15.2 to 10,668 m (–50 to 35,000 ft)

3At 35°C (95°F), the maximum operating altitude is 914 m (3000 ft).

Regulatory Notices

FCC (U.S. only)

Class B

IC Notice (Canada only)

Class B

CE Notice

Class B

VCCI Notice (Japan only)

Class B

NOM O24 Information (Mexico only)

 

 

 

Image 29
Contents Model MCM Dell Dimension 2100 System ReferenceBack to Contents Diagnostic CodesDiagnostic Codes Post Beep Codes System Messages Diagnostic Codes DefinitionReseat the memory modules Post Beep CodesSystem Beep Codes Possible Cause System Messages System MessagesOperating system cannot be located on drive a or drive C Click Device Manager Click the Device Manager tabBack to Contents Front Panel Controls and Lights Dell Dimension 2100 System ReferenceBack Panel Front Panel Back PanelTypographical Conventions Conventions Dell Dimension 2100 System ReferenceTypographical Conventions Printed Documentation Documentation Dell Dimension 2100 System ReferenceOnline Documentation Printed Documentation Online DocumentationBack to Contents Your Computer’s Drivers Drivers Dell Dimension 2100 System ReferenceUsing the Dell Dimension ResourceCD to Reinstall Drivers Back to Contents Overview Precautionary MeasuresRecommended Tools You have the recommended toolsCover Rotating the Power SupplyRotate the power supply back into place Remove the computer cover Upper 3.5-Inch Drive Inch Front Panel InsertInsert TabsInch Drive Lower 3.5-Inch Floppy DriveHard Drive Control Panel Power Supply and Fan AssemblyCards Remove the front coverMemory Remove the computer cover Rotate the power supplyConnector Remove and replace the microprocessor chip from the socket Heat SinkMicroprocessor System Board BatteryReplace the computer cover, and start the computer Remove the computer cover Remove the power supplyBack to Contents Expansion Bus System InformationVideo DrivesPorts Physical PowerEnvironmental Regulatory NoticesIRQ Assignments Default Dell-Installed Card PlacementIRQ Line System Resource Card SlotMain Screen System Setup Program Dell Dimension 2100 System ReferenceEntering the System Setup Program Advanced Screen Menu Options Function Advanced ScreenMain Screen Menu Options Function Displays the IDE Configuration submenu Interrupt Primary IDE Master SubmenuMode Base I/OEvent Log Configuration Submenu Diskette Configuration SubmenuDiskette Configuration Submenu Options Primary IDE Master Submenu OptionsEvent Log Configuration Submenu Options Video Configuration SubmenuVideo Configuration Submenu Option Function Security ScreenSecurity Screen Options Function Boot ScreenBoot Screen Options Exit Screen Network DisabledFloppy Exit Screen OptionsClearing Nvram Enter the system setup programBack-Panel Features Technical Overview Dell Dimension 2100 System ReferenceSystem Board Connectors and Sockets Internal ViewPower Supply System Board Configuration JumperJumper Setting Jumper DescriptionDC Power Connector P1 DC Power Cables DC Power Connector Pin AssignmentsDC Voltage Ranges Voltage Range CurrentDC Power Connector P2 Control Panel Connector J9F2 Pin AssignmentsDC Power Connector P3 DC Power Connectors P4, P5, and P6Back to Contents