Dell Dimension 2100 technical specifications Floppy, Network Disabled, Exit Screen Options

Page 38

1st Boot Device

this option are Power On or Stays Off (default).

Determines which device the computer tries to boot from first. Use the up- or down-arrow key to highlight a device. Settings for this option are as follows:

•Floppy

•ARMD FDD

•ARMD HDD

•IDE-HDD

•ATAPI CD-ROM

•SCSI*

•Network*

•Disabled

*Where SCSI or Network is the name of the installed device.

2nd Boot Device

3rd Boot Device

4th Boot Device

Determines which device the computer tries to boot from if it cannot boot from the device selected for 1st Boot Device. Settings for this option are the same as those for 1st Boot Device except for NETWORK.

Determines which device the computer tries to boot from if it cannot boot from the devices selected for 1st Boot Device and 2nd Boot Device. Settings for this option are the same as those for 1st Boot Device except for NETWORK and SCSI.

Determines which device the computer tries to boot from if it cannot boot from the devices selected for 1st Boot Device, 2nd Boot Device, and 3rd Boot Device. Settings for this option are the same as those for 1st Boot Device except for NETWORK and SCSI.

Exit Screen

Table 12. Exit Screen Options

Option

Exit Saving

Changes

Exit Discarding Changes

Load Setup

Defaults

Load Custom Defaults

Save Custom Defaults

Discard Changes

Function

Saves any changes you have made, exits the system setup program, and restarts the computer.

Discards any changes you have made, exits the system setup program, and restarts the computer.

Discards any changes you have made and reverts all options to their defaults, but does not exit the system setup program.

Loads any settings saved using the Save Custom Defaults option. Press <Enter>. Then press the spacebar to select Yes or No at the confirmation pop-up menu, and press <Enter> again.

Saves any changes you have made, but does not exit the system setup program.

Discards any changes you have made and reverts all options to their last saved settings, but does not exit the system setup program.

Image 38

Contents Dell Dimension 2100 System Reference Model MCMDiagnostic Codes Post Beep Codes System Messages Diagnostic CodesBack to Contents Diagnostic Codes DefinitionReseat the memory modules Post Beep CodesSystem Beep Codes Possible Cause System Messages System MessagesOperating system cannot be located on drive a or drive C Click the Device Manager tab Click Device ManagerBack to Contents Back Panel Controls and Lights Dell Dimension 2100 System ReferenceFront Panel Front Panel Back PanelTypographical Conventions Conventions Dell Dimension 2100 System ReferenceTypographical Conventions Online Documentation Documentation Dell Dimension 2100 System ReferencePrinted Documentation Printed Documentation Online DocumentationBack to Contents Your Computer’s Drivers Drivers Dell Dimension 2100 System ReferenceUsing the Dell Dimension ResourceCD to Reinstall Drivers Back to Contents Recommended Tools Precautionary MeasuresOverview You have the recommended toolsCover Rotating the Power SupplyRotate the power supply back into place Remove the computer cover Insert Inch Front Panel InsertUpper 3.5-Inch Drive TabsLower 3.5-Inch Floppy Drive Inch DriveHard Drive Cards Power Supply and Fan AssemblyControl Panel Remove the front coverMemory Remove the computer cover Rotate the power supplyConnector Heat Sink Remove and replace the microprocessor chip from the socketMicroprocessor Battery System BoardRemove the computer cover Remove the power supply Replace the computer cover, and start the computerBack to Contents System Information Expansion BusVideo DrivesPorts Environmental PowerPhysical Regulatory NoticesIRQ Line System Resource Default Dell-Installed Card PlacementIRQ Assignments Card SlotMain Screen System Setup Program Dell Dimension 2100 System ReferenceEntering the System Setup Program Advanced Screen Menu Options Function Advanced ScreenMain Screen Menu Options Function Displays the IDE Configuration submenu Mode Primary IDE Master SubmenuInterrupt Base I/ODiskette Configuration Submenu Options Diskette Configuration SubmenuEvent Log Configuration Submenu Primary IDE Master Submenu OptionsVideo Configuration Submenu Option Function Video Configuration SubmenuEvent Log Configuration Submenu Options Security ScreenSecurity Screen Options Function Boot ScreenBoot Screen Options Floppy Network DisabledExit Screen Exit Screen OptionsEnter the system setup program Clearing NvramSystem Board Connectors and Sockets Technical Overview Dell Dimension 2100 System ReferenceBack-Panel Features Internal ViewJumper Setting System Board Configuration JumperPower Supply Jumper DescriptionDC Voltage Ranges DC Power Cables DC Power Connector Pin AssignmentsDC Power Connector P1 Voltage Range CurrentDC Power Connector P3 Control Panel Connector J9F2 Pin AssignmentsDC Power Connector P2 DC Power Connectors P4, P5, and P6Back to Contents