D-Link DSL-1500G All connections must configure, Connection Profile, Login Password, Idle Time

Page 26

DSL-1500G SHDSL Ethernet Router User’s Guide

The parameters available to be configured in the Router/Bridge Configuration menu change according to the Connection Profile configured.

NOTICE: If you must change the Connection Profile, change it to the desired setting and click the OK button without making any other changes. Save the changes and reboot the device. Upon restarting continue to configure any remaining settings that need to be changed in the Router/Bridge Configuration Menu. It will again be necessary to save settings and restart the Router to establish the WAN connection.

All connections must configure:

 

Use this drop-down menu to select the connection profile. If your

Connection Profile

account uses a connection protocol that is not listed, it will be necessary

to create a new connection profile. Also, if your DSL connection uses

 

different VPI/VCI values, a new connection profile must be created. See

 

the next section, Adding and Changing a Connection Profile.

Encapsulation Method Select LLC or VC Mux as instructed by your service provider.

PPPoA and PPPoE connection profiles must configure:

 

Login User Name

Type in the account user name used for authentication by your network

 

service provider.

 

 

 

 

 

 

Login Password

Type in the account password used for authentication by your network

 

service provider.

 

 

 

Confirm Password

Type the same password to confirm it.

 

 

 

 

Authentication

Choose the security protocol used to confirm the identity of the

 

subscriber. Choose chap (default) or pap form the drop-down menu.

 

 

 

 

Select enabled or disabled. When this function is enabled the router will

 

Connect on Demand

connect any workstation on your LAN to the Internet upon request. If this

 

function is disabled, it will be necessary to access this menu and hit the

 

 

Connect button each time you want to establish a connection to the

 

 

WAN or the Internet.

 

 

A value of 0 means that the PPP connection will remain connected. If

 

 

your network account is billed according to the amount of time the

 

Idle Time

Router is actually connected to the Internet, enter an appropriate Idle

 

Time value (in seconds). This will disconnect the Router after the WAN

 

 

 

 

connection has been idle for the amount of time specified. The default

 

 

value = 0.

 

IPoA connection profiles must configure:

 

 

 

 

 

This is enabled by default and therefore no IP settings need to be

 

IP Unnumbered

entered for the account. If this is disabled, (global) IP settings must be

 

 

configured for the WAN interface.

 

IP Address

If IP Unnumbered is disabled, type in the WAN IP address for the

 

account.

 

 

 

Subnet Mask

If IP Unnumbered is disabled, type in the subnet mask for the WAN

 

interface.

 

 

16

Image 26
Contents User’s Guide Wichtige Sicherheitshinweise Hardware Limited WarrantyLink Offices for Registration and Warranty Service SoftwareFCC Warning TrademarksCopyright Statement Table of Contents Technical Specifications Before You Start Guide OverviewOperating System Requirements for InstallationInstallation Overview Web BrowserAccount Information User Name and Password Packing ListPage Router Description and Operation About ShdslProduct Features Standards Compatibility and Compliance Status PowerFront Panel LED Display EthernetRear Panel Cable Connections Connect Router to Ethernet Power On RouterFactory Reset Button Select LocationConfigure IP Settings on Your Computer Wan Configuration SummaryDhcp Configuration for Windows NT Configure Dhcp for Windows 95/98/MeConfigure Dhcp for Windows 2000/XP Renew IP Settings in Windows for Dhcp ClientAccess the Configuration Manager LoginEnter User Name and Password Configure the Router Configuring the WAN Connection First Time SetupRouter/Bridge Configuration Bridge with RFC 1483 only Accessing the Web Manager Web-based Management GuideWeb Manager Layout Web Manager GUI Web Manager Folders MenusRouter/Bridge Configuration Router ConfigurationRouter/Bridge Configuration Confirm Password All connections must configureLogin Password AuthenticationConnect / Disconnect Buttons Bridge ConfigurationBridge with RFC 1483 Router/Bridge Configuration menu IPoA Configuration Router with IPoA Router/Bridge Configuration menuProfile Name Adding and Changing Connection ProfilesConnection Profile menu Connection TypeAdd/Change Connection Profile DSL-1500G Shdsl Ethernet Router User’s Guide Configuring LAN IP Settings Ethernet IP Address MenuProxy DNS Proxy DNS SettingsProxy DNS Menu Get DNS IP automaticallyDhcp Configuration NAT Configuration NAT Configuration MenuIP Masquerade Pass Through IP Masquerade Timer IP Masquerade TimerPort Redirection Port Redirection MenuInternet Select index to setProtocol Start PortItem Name Static Route ConfigurationStatic Route Configuration Table GatewayAdvanced Filter & Firewall Filter & Firewall Main MenuDestination Pass or BlockSource RIP RIP MenuDate & Time Settings Date & Time ConfigurationUPnP Configuration UPnPATM Loopback Test System MaintenanceATM Loopback Screen F4/F5Save Changes System Username and PasswordSystem User Name and Password Menu Save Changes MenuFactory Reset Screen Factory ResetUpdate Firmware Update Firmware ScreenConfiguration Maintenance Screen Configuration File MaintenanceRemote Administration Access Remote Administration AccessConnection Status Shdsl Line SettingLine Retrain Summary System SummaryDhcp Configuration ConfigurationPPP Login Information Login User Name NAT ConfigurationDhcp Allocation Table Dhcp Allocation TablePort Redirection Summary Port Redirection SummaryRuntime Routing Table Runtime Routing TableFilter and Firewall Summary Filtering & Firewall SummaryLine Condition Weight TemperatureDimensions SafetyATM/DSL IPv4Page Offices Netherlands Link Benelux Registration Card Print, type or use block letters