D-Link DSL-1500G manual Pass or Block, Source, Destination

Page 42

DSL-1500G SHDSL Ethernet Router User’s Guide

Define these variables for each filter rule:

 

When adding a new rule, choose the Not selected option from the drop-

Select index to set

down menu first. This will automatically assign the next available index

number to the new rule. If you are deleting or modifying an existing rule,

 

 

select it and click the appropriate button to the right.

 

 

Item Name

Name filtering rule defined here.

 

 

State

Select Enabled to start using the static route when it is applied. To save a

route you do not want to use now for later use without deleting it you can

 

choose Disabled.

 

 

Pass or Block

Choose Block to drop packets as defined by the rule. The default Pass will

route data without restriction as a normal packet.

 

 

 

Interface

Choose Ethernet or select a WAN interface. If you have a single PVC and

have not modified the name of the WAN interface, it appears here as ISP1

 

(the default name for the WAN interface).

 

 

Protocol

Select ICMP, TCP, UDP or All to pass or block packets of that protocol type.

 

 

Source

Type in the source IP address and select the Subnet Mask to pass or block

packets form that IP address.

 

 

 

<

specifies the port numbers less than and equal to the Start Port number

>

specifies the port numbers greater than and equal to the Start Port number

=sets the port number equal to the Start Port if there is no End Port specified; if an End Port number is specified, this defines a range of ports to filter. The range is defined as the port numbers between the Start Port and End Port, including the Start and End Port numbers.

Start Port

For a range of ports, this will be the first port in the range. For a single port

enter the port number.

 

 

 

End Port

For a range of ports, this will be the last port in the range. For a single port

just enter the same port number entered in Start Port.

 

 

 

Destination

Type in the destination IP address and select the Subnet Mask to pass or

block packets destined to that IP address.

 

 

 

To delete or modify an existing rule, select the index number and click the action button for Delete or Modify. Clicking on the Clear button will set the variables to the blank or default setting.

Each new rule that is added will appear in the entry table at the top of the web page. When you have configured all the rules you want to use, click on the Apply button. You can save and reboot the system now, or continue to configure the Router.

32

Page 41 Page 43
Image 42
Page 41 Page 43
Contents User’s Guide Wichtige Sicherheitshinweise Hardware Limited WarrantyLink Offices for Registration and Warranty Service SoftwareTrademarks Copyright StatementFCC Warning Table of Contents Technical Specifications Before You Start Guide OverviewOperating System Requirements for InstallationInstallation Overview Web BrowserAccount Information User Name and Password Packing ListPage Router Description and Operation About ShdslProduct Features Standards Compatibility and Compliance Status PowerFront Panel LED Display EthernetRear Panel Cable Connections Connect Router to Ethernet Power On RouterFactory Reset Button Select LocationConfigure IP Settings on Your Computer Wan Configuration SummaryDhcp Configuration for Windows NT Configure Dhcp for Windows 95/98/MeConfigure Dhcp for Windows 2000/XP Renew IP Settings in Windows for Dhcp ClientAccess the Configuration Manager LoginEnter User Name and Password Configure the Router Configuring the WAN Connection First Time SetupRouter/Bridge Configuration Bridge with RFC 1483 only Accessing the Web Manager Web-based Management GuideWeb Manager Layout Web Manager GUI Web Manager Folders MenusRouter Configuration Router/Bridge ConfigurationRouter/Bridge Configuration Confirm Password All connections must configureLogin Password AuthenticationBridge Configuration Bridge with RFC 1483 Router/Bridge Configuration menuConnect / Disconnect Buttons IPoA Configuration Router with IPoA Router/Bridge Configuration menuProfile Name Adding and Changing Connection ProfilesConnection Profile menu Connection TypeAdd/Change Connection Profile DSL-1500G Shdsl Ethernet Router User’s Guide Configuring LAN IP Settings Ethernet IP Address MenuProxy DNS Proxy DNS SettingsProxy DNS Menu Get DNS IP automaticallyDhcp Configuration NAT Configuration NAT Configuration MenuIP Masquerade Pass Through IP Masquerade Timer IP Masquerade TimerPort Redirection Port Redirection MenuInternet Select index to setProtocol Start PortItem Name Static Route ConfigurationStatic Route Configuration Table GatewayAdvanced Filter & Firewall Filter & Firewall Main MenuPass or Block SourceDestination RIP RIP MenuDate & Time Settings Date & Time ConfigurationUPnP Configuration UPnPATM Loopback Test System MaintenanceATM Loopback Screen F4/F5Save Changes System Username and PasswordSystem User Name and Password Menu Save Changes MenuFactory Reset Screen Factory ResetUpdate Firmware Update Firmware ScreenConfiguration Maintenance Screen Configuration File MaintenanceRemote Administration Access Remote Administration AccessShdsl Line Setting Line RetrainConnection Status Summary System SummaryDhcp Configuration ConfigurationPPP Login Information Login User Name NAT ConfigurationDhcp Allocation Table Dhcp Allocation TablePort Redirection Summary Port Redirection SummaryRuntime Routing Table Runtime Routing TableFilter and Firewall Summary Filtering & Firewall SummaryLine Condition Weight TemperatureDimensions SafetyATM/DSL IPv4Page Offices Netherlands Link Benelux Registration Card Print, type or use block letters
Top Page Image Contents