D-Link DSL-1500G System Maintenance, ATM Loopback Screen, ATM Loopback Test, F4/F5, Etoe/segment

Page 46

DSL-1500G SHDSL Ethernet Router User’s Guide

System Maintenance

The Mainatenance folder in the web mananger contains links to menus used for sytem maintenance functions including firmware upgarde and username/password configuration.

ATM Loopback Test

ATM loopback tests are used to verify connectivity and path integrity along a specified ATM circuit. In the test, a cell is sent to an endpoint or to the end of the first segment of the ATM path. If the path is available and the connections are functioning, an test cell will be returned along the same ATM path and be detected by the device. This is very similar to a Ping test. The test can help to determine if connectivity problems originate from outside the LAN.

 

 

ATM Loopback Screen

To perform the test, define the following parameters:

 

 

 

 

VPI

Type in the VPI setting used for the network connection.

 

 

 

 

VCI

Type in the VCI setting used for the network connection.

 

 

 

 

 

Choose F4 (Virtual Path) or F5 (Virtual Connection) from the pull-down menu to

 

 

define the flow type. An F4 flow test is used to verify that ATM network information

 

 

(ATM cells) can be shared between network elements. This information is used

 

F4/F5

within virtual paths to report an unavailable path or a virtual path that cannot be

 

guaranteed. An F5 flow test is also used to verify that ATM network information can

 

 

 

 

be shared between network elements. This information is used within virtual

 

 

connections to report degraded virtual channel performance such as late arriving

 

 

cells, lost cells, and cell insertion problems.

 

 

 

 

etoe/segment

Select the test type from the remaining pull-down menu. Choose End-to-Endto test

 

the entire path from the Router to the ATM connection endpoint. Choose segment

 

 

to test the path from the Router to the end of the first ATM connection segment.

 

 

 

 

 

A success or fail message appears here after the test is completed. If the reply cell

 

Status

is received within the standard-defined time, the Status will read OK. This indicates

 

that the specified test path is functioning normally and all connections were

 

 

 

 

successful. If the Status reads Fail, there is a fault in the segment or path tested.

 

 

 

When all the test parameters have been specified, click on the Loop Test button to initiate the test.

36

Page 45 Page 47
Image 46
Page 45 Page 47
Contents User’s Guide Wichtige Sicherheitshinweise Hardware Limited WarrantyLink Offices for Registration and Warranty Service SoftwareCopyright Statement TrademarksFCC Warning Table of Contents Technical Specifications Before You Start Guide OverviewOperating System Requirements for InstallationInstallation Overview Web BrowserAccount Information User Name and Password Packing ListPage Router Description and Operation About ShdslProduct Features Standards Compatibility and Compliance Status PowerFront Panel LED Display EthernetRear Panel Cable Connections Connect Router to Ethernet Power On RouterFactory Reset Button Select LocationConfigure IP Settings on Your Computer Wan Configuration SummaryDhcp Configuration for Windows NT Configure Dhcp for Windows 95/98/MeConfigure Dhcp for Windows 2000/XP Renew IP Settings in Windows for Dhcp ClientAccess the Configuration Manager LoginEnter User Name and Password Configure the Router Configuring the WAN Connection First Time SetupRouter/Bridge Configuration Bridge with RFC 1483 only Accessing the Web Manager Web-based Management GuideWeb Manager Layout Web Manager GUI Web Manager Folders MenusRouter/Bridge Configuration Router ConfigurationRouter/Bridge Configuration Confirm Password All connections must configureLogin Password AuthenticationBridge with RFC 1483 Router/Bridge Configuration menu Bridge ConfigurationConnect / Disconnect Buttons IPoA Configuration Router with IPoA Router/Bridge Configuration menuProfile Name Adding and Changing Connection ProfilesConnection Profile menu Connection TypeAdd/Change Connection Profile DSL-1500G Shdsl Ethernet Router User’s Guide Configuring LAN IP Settings Ethernet IP Address MenuProxy DNS Proxy DNS SettingsProxy DNS Menu Get DNS IP automaticallyDhcp Configuration NAT Configuration NAT Configuration MenuIP Masquerade Pass Through IP Masquerade Timer IP Masquerade TimerPort Redirection Port Redirection MenuInternet Select index to setProtocol Start PortItem Name Static Route ConfigurationStatic Route Configuration Table GatewayAdvanced Filter & Firewall Filter & Firewall Main MenuSource Pass or BlockDestination RIP RIP MenuDate & Time Settings Date & Time ConfigurationUPnP Configuration UPnPATM Loopback Test System MaintenanceATM Loopback Screen F4/F5Save Changes System Username and PasswordSystem User Name and Password Menu Save Changes MenuFactory Reset Screen Factory ResetUpdate Firmware Update Firmware ScreenConfiguration Maintenance Screen Configuration File MaintenanceRemote Administration Access Remote Administration AccessLine Retrain Shdsl Line SettingConnection Status Summary System SummaryDhcp Configuration ConfigurationPPP Login Information Login User Name NAT ConfigurationDhcp Allocation Table Dhcp Allocation TablePort Redirection Summary Port Redirection SummaryRuntime Routing Table Runtime Routing TableFilter and Firewall Summary Filtering & Firewall SummaryLine Condition Weight TemperatureDimensions SafetyATM/DSL IPv4Page Offices Netherlands Link Benelux Registration Card Print, type or use block letters
Top Page Image Contents