NETGEAR JNR1010V2, WNR2020, WNR618, WNR614 Factory Settings, Router factory default settings

Page 76

N150 and N300 Wireless Routers

Factory Settings

You can return the router to its factory settings. Use the end of a paper clip or some other similar object to press and hold the WPS/Reset button on the back panel of the router for at least four seconds. The router resets, and returns to the factory settings that are shown in the following table.

Table 4. Router factory default settings

Feature

 

Default Behavior

 

 

 

Router login

User login URL

www.routerlogin.com or www.routerlogin.net

 

 

 

 

User name (case-sensitive)

admin

 

 

 

 

Login password (case-sensitive)

password

 

 

 

Internet

WAN MAC address

Use default hardware address

connection

 

 

WAN MTU size

1500

 

 

 

 

 

Port speed

AutoSensing

 

 

 

Local area

LAN IP

192.168.1.1

network (LAN)

 

 

Subnet mask

255.255.255.0

 

 

 

 

 

DHCP server

Enabled

 

 

 

 

DHCP range

192.168.1.2 to 192.168.1.254

 

 

 

 

Time zone

United States is Pacific Time; otherwise, varies by region

 

 

 

 

Time zone adjusted for daylight

Disabled

 

saving time

 

 

 

 

Wireless

Wireless communication

Enabled

 

 

 

 

SSID name

Preset. For information, see the product label.

 

 

 

Network key (password)

 

 

 

 

 

 

Broadcast SSID

Enabled

 

 

 

 

Transmission speed

Auto

 

 

Note: Maximum wireless signal rate derived from IEEE

 

 

Standard 802.11 specifications. Actual throughput varies.

 

 

Network conditions and environmental factors, including

 

 

volume of network traffic, building materials and

 

 

construction, and network overhead lower actual data

 

 

throughput rate.

 

 

 

 

Country/region

United States in the US; otherwise, varies by region

 

 

 

 

RF channel

Auto

 

 

 

 

Operating mode

Up to 300 Mbps or up to 150Mbps for model JNR1010v2

 

 

 

Supplemental Information

76

Page 75 Page 77
Image 76
Page 75 Page 77
Contents N150 and N300 Wireless Routers ModelsCompliance SupportTrademarks Contents Manage Your Network Appendix a Supplemental Information Hardware Setup Front Panel LEDs Hardware FeaturesBack Panel Position Your Router  To prepare your router for installation To position your router Cable Your Router  To cable your routerVerify the Cabling Connect to the Network Access the Router Wired Connection WiFi Connection To use WPS to connect to the WiFi network  To find and select the WiFi networkUse a Web Browser to Access the Router Types of LoginsNetgear genie Automatic Internet Setup Log In to the Router  To use Netgear genie to set up your router To log in to the router Connect to the Network and Access the Router Specify Your Internet Settings  To use the Setup Wizard Use the Internet Setup WizardSelect Advanced Setup Wizard Specify an Internet Connection Without a Login Manually Set Up the Internet Connection To specify the Internet connection settings Specify an Internet Connection That Uses a Login  To view or change the basic Internet setupSelect Internet Change the MTU Size Select Advanced Setup WAN Setup  To change the MTU sizeCommon MTU sizes Networking View or Change WAN Settings  To view or change the WAN settingsSet Up a Default DMZ Server Change the Router’s Device Name  To set up a default DMZ server To change the router’s device name Change the LAN TCP/IP Settings Select Advanced Setup LAN Setup To change the LAN TCP/IP settings LAN IP addressRIP Version list, select one of the following Specify the IP Addresses that the Router Assigns  To disable the Dhcp server feature in the router Disable the Dhcp Server Feature in the RouterReserve LAN IP Addresses  To reserve an IP address  To edit a reserved address entryUse the WPS Wizard for WiFi Connections  To delete a reserved address entry To use the WPS Wizard Select Advanced WPS WizardSpecify Basic WiFi Settings  To specify basic wireless settingsSelect Wireless Change the WiFi Security Option  To change the WPA settings To set up a guest network Set Up a Guest NetworkSelect Guest Network Enable or Disable the Wireless Radio Control the Wireless Radio To enable or disable the wireless radio Select Advanced Advanced Setup Wireless Settings Set Up a Wireless Schedule To set up the wireless schedule Set up a Wireless Access List Networking Wireless Distribution System Specify WPS Settings To specify WPS Settings  To set up the base station Set Up the Base StationSelect Advanced Advanced Setup Wireless Repeating Function Select the Enable Wireless Repeating Function check box Set Up a Repeater To configure the router as a repeater Complete the Repeater IP Address field Select Advanced Advanced Setup Static Routes  To set up a static routeStatic Routes  To edit a static route  To delete a static route View Devices Currently on the Network To view devices on the network Improve Network Connections with Universal Plug and Play  To enable Universal Plug and PlaySelect Attached Devices Select Advanced Advanced Setup UPnP Manage Your Network  To check for new firmware and update your router Update the Router FirmwareSelect Advanced Administration Firmware Update Change the admin Password Recover the admin Password To set the password for the user name admin Select Advanced Administration Set PasswordSelect the Enable Password Recovery check box  To recover your passwordView Router Status  To view router status and usage informationClick the Advanced tab LAN PortView the Internet Connection Settings  To view the Internet connection settingsDisplay Internet Port Statistics  To display Internet port statisticsView the Internet Connection Status  To check the Internet connection status To change the router Dhcp connection settings Dhcp ConnectionView Wireless Settings  To change the router PPPoE connection settings To change the router Pptp connection settings  To view the wireless settingsView Guest Network Settings  To view the guest network settingsReboot the Router Manage the Configuration File To reboot the router Do not interrupt the reboot processBack Up Settings Restore Configuration Settings To back up the router’s configuration settings Select Advanced Administration Backup SettingsErase Configuration Settings Troubleshooting Admin Password Forgotten PasswordsWiFi Passwords WiFi Connections  To use a wired connection to view WiFi settingsApply Power to the Router and Check the LEDs  To apply power to the router and check the LEDsChanges Not Saved Troubleshoot with the LEDsPower LED Is Off or Blinking Power LED Stays AmberAll LEDs Remain Lit Internet LEDs Is OffWiFi LED Is Off Cannot Log In to the RouterRouter Cannot Access the Internet  To check the WAN IP addressTroubleshoot a PPPoE Internet Connection Troubleshoot Internet Browsing To troubleshoot a PPPoE Internet connection Test the LAN Path to Your Router Troubleshoot Your Network Using the Ping Utility To ping the router from a computer running Windows Test the Path from Your Computer to a Remote Device Request timed outTroubleshoot IP Addresses Supplemental Information Factory Settings Router factory default settingsTechnical Specifications Router specifications
Related manuals
Manual 91 pages 45.66 Kb
Top Page Image Contents