NETGEAR WNR618, WNR2020, WNR614, JWNR2010v5 RIP Version list, select one of the following

Page 29

N150 and N300 Wireless Routers

4.Select ADVANCED > Setup > LAN Setup.

5.In the IP Address field, type the IP address.

6.In the IP Subnet Mask, type the subnet mask of the router.

The IP address and subnet mask identifies which addresses are local to a specific device and which must be reached through a gateway or router.

7.Change the RIP settings.

Router Information Protocol (RIP) allows a router to exchange routing information with other routers.

a.In the RIP Direction list, select one of the following:

-Both. The router broadcasts its routing table periodically and incorporates information that it receives.

-Out Only. The router broadcasts its routing table periodically.

-In Only. The router incorporates the RIP information that it receives.

b.In the RIP Version list, select one of the following:

-Disabled. This is the default setting.

-RIP-1. This format is universally supported. It is adequate for most networks, unless you have an unusual network setup.

-RIP-2. This format carries more information. Both RIP-2B and RIP-2M send the routing data in RIP-2 format. RIP-2B uses subnet broadcasting. RIP-2M uses multicasting.

8.Click the Apply button. Your changes are saved.

If you changed the LAN IP address of the router, you are disconnected when this change takes effect.

9.To reconnect, close your browser, relaunch it, and log in to the router

Networking

29

Image 29

Contents Models N150 and N300 Wireless RoutersTrademarks SupportCompliance Contents Manage Your Network Appendix a Supplemental Information Hardware Setup Back Panel Hardware FeaturesFront Panel LEDs  To position your router  To prepare your router for installationPosition Your Router  To cable your router Cable Your RouterVerify the Cabling Connect to the Network Access the Router WiFi Connection Wired Connection To use WPS to connect to the WiFi network  To find and select the WiFi networkNetgear genie Automatic Internet Setup Types of LoginsUse a Web Browser to Access the Router  To log in to the router  To use Netgear genie to set up your routerLog In to the Router Connect to the Network and Access the Router Specify Your Internet Settings Select Advanced Setup Wizard Use the Internet Setup Wizard To use the Setup Wizard  To specify the Internet connection settings Manually Set Up the Internet ConnectionSpecify an Internet Connection Without a Login  To view or change the basic Internet setup Specify an Internet Connection That Uses a LoginSelect Internet Change the MTU Size  To change the MTU size Select Advanced Setup WAN SetupCommon MTU sizes Networking  To view or change the WAN settings View or Change WAN SettingsSet Up a Default DMZ Server  To change the router’s device name  To set up a default DMZ serverChange the Router’s Device Name Select Advanced Setup LAN Setup Change the LAN TCP/IP Settings To change the LAN TCP/IP settings LAN IP addressRIP Version list, select one of the following Specify the IP Addresses that the Router Assigns Reserve LAN IP Addresses Disable the Dhcp Server Feature in the Router To disable the Dhcp server feature in the router  To edit a reserved address entry  To reserve an IP address To delete a reserved address entry Use the WPS Wizard for WiFi Connections To use the WPS Wizard Select Advanced WPS Wizard To specify basic wireless settings Specify Basic WiFi SettingsSelect Wireless  To change the WPA settings Change the WiFi Security OptionSelect Guest Network Set Up a Guest Network To set up a guest network  To enable or disable the wireless radio Control the Wireless RadioEnable or Disable the Wireless Radio  To set up the wireless schedule Set Up a Wireless ScheduleSelect Advanced Advanced Setup Wireless Settings Set up a Wireless Access List Networking  To specify WPS Settings Specify WPS SettingsWireless Distribution System Select Advanced Advanced Setup Wireless Repeating Function Set Up the Base Station To set up the base station  To configure the router as a repeater Set Up a RepeaterSelect the Enable Wireless Repeating Function check box Complete the Repeater IP Address field Static Routes  To set up a static routeSelect Advanced Advanced Setup Static Routes  To edit a static route  To view devices on the network View Devices Currently on the Network To delete a static route Select Attached Devices  To enable Universal Plug and PlayImprove Network Connections with Universal Plug and Play Select Advanced Advanced Setup UPnP Manage Your Network Select Advanced Administration Firmware Update Update the Router Firmware To check for new firmware and update your router Recover the admin Password Change the admin Password To set the password for the user name admin Select Advanced Administration Set Password To recover your password Select the Enable Password Recovery check box To view router status and usage information View Router StatusClick the Advanced tab LAN Port To view the Internet connection settings View the Internet Connection SettingsDisplay Internet Port Statistics  To display Internet port statistics To check the Internet connection status View the Internet Connection StatusDhcp Connection  To change the router Dhcp connection settings To change the router PPPoE connection settings View Wireless Settings To change the router Pptp connection settings  To view the wireless settings To view the guest network settings View Guest Network SettingsManage the Configuration File Reboot the Router To reboot the router Do not interrupt the reboot processRestore Configuration Settings Back Up Settings To back up the router’s configuration settings Select Advanced Administration Backup SettingsErase Configuration Settings Troubleshooting WiFi Passwords Forgotten PasswordsAdmin Password  To use a wired connection to view WiFi settings WiFi Connections To apply power to the router and check the LEDs Apply Power to the Router and Check the LEDsChanges Not Saved Troubleshoot with the LEDsPower LED Stays Amber Power LED Is Off or BlinkingAll LEDs Remain Lit Internet LEDs Is OffCannot Log In to the Router WiFi LED Is Off To check the WAN IP address Router Cannot Access the Internet To troubleshoot a PPPoE Internet connection Troubleshoot Internet BrowsingTroubleshoot a PPPoE Internet Connection  To ping the router from a computer running Windows Troubleshoot Your Network Using the Ping UtilityTest the LAN Path to Your Router Request timed out Test the Path from Your Computer to a Remote DeviceTroubleshoot IP Addresses Supplemental Information Router factory default settings Factory SettingsRouter specifications Technical Specifications

Related manuals

Manual 91 pages 45.66 Kb