Asante Technologies 1012 RJ-45 Modular Jack to Wall Jack Pinouts, RJ-45 to RJ-45 Crossover Cable

Page 104

Appendix C — Pinouts and Cable Specifications

RJ-45 Modular Jack to Wall Jack Pinouts

These pin numbers are for an Asanté 10BaseT card or MAU posi- tioned correctly with the notch on the 8-pin modular jack down. Pin 1 is the leftmost pin, and pin 8 is the right-most pin.

1

TD+

Data Transmit positive

2

TD-

Data Transmit negative

3

TD+

Data Transmit positive

4

TD-

Data Transmit negative

1 2 3 4 5 6 7 8

Figure C-3 RJ-45 Wall Jack to Modular Jack Pinouts

RJ-45 to RJ-45 Crossover Cable

1

3

2

6

3

1

6

2

Figure C-4 Crossover RJ-45 Cable

Note:This manual assumes that straight-through cabling is used for all applications, except where specifically noted.

Page C-4

Image 104
Contents AsantéBridge Users’ Guide Trademarks Tell Us What You Think Page Table of Contents Configuring a Redundant Link Setting Up Out-of-Band LinksConnecting a VT100 Terminal Default Settings AsantéBridge 1012 Local ManagementList of Figures Figure C-4 Crossover RJ-45 Cable page C-4 Introduction Introduction About ThisManual Intended Audience Conventions Used In This Manual Intended AudienceTell Us What You Think Technical SupportQuick Start Quick Start Before YouStart Introducing AsantéBridge Introducing the AsantéBridgeBridging Between Two Segments AsantéBridge Features SnmpFront Panel Quick ViewAsantéBridge Quick View RJ45 Port Connectors Bridge External Port Status LEDBridge Spanning Tree Status LEDs Bridge Hub Port Status LEDs3in1 Port RJ21 Port ConnectorAsantéBridge 1012 Rear Panel Through/End DIP Switch Bridge External Port AUIBridge External Port Link/Receive LED Bridge External Port Collision LEDPC/Terminal DIP Switch AC Power ConnectorOn/Off Switch FanInterpreting LEDs FlashingInstalling the AsantéBridge Installing AsantéBridge 1012Preparing for the Installation Unpacking the AsantéBridge Basic Installation ProceduresTools Positioning the AsantéBridge Asante´HubRack-mounting the AsantéBridge Page Connecting Two Segments to the AsantéBridge Dividing the Network into SegmentsShown below About Spanning TreesWhat You Need Connecting Devices to the AsantéBridgeUsing the front panel RJ45 ports Using the rear panel RJ21 connector Configuration OptionsQuick Start Connecting to the Network Connecting to the Network Before You StartAbout Bridging About BridgingSimple Transparent Bridge Bridging between segmentsAbout Bridging Spanning Tree Like thisRedundant bridging Using the 3in1 Port Connecting to the BNC PortUsing the 3in1 Port Interconnecting Hubs on Thin Ethernet BackboneConnecting to the AUI Port Interconnecting Using Foirl Fiber Optic Inter-Repeater LinkInterconnecting to Thick Ethernet Backbone Connecting to the RJ45 in and Out Ports Connecting an In-Band Daisychaining 10BaseT Configuring a Redundant LinkChecking the Link Configuring a Redundant Link An Example ConfigurationIf the Main Hub Goes Down If a Link Goes Down to the Main HubInterconnecting Hubs Setting Up Out-of-Band LinksSetting Up Out-of-Band Links 10 Connecting the Asanté Management Station for Out-of-Band Recommended Method Distance RestrictionsThrough/End Switch Configuring Hub DIP SwitchesPC/Terminal Switch Connecting a VT100 Terminal Connecting a VT100 TerminalDefault Settings Lists the factory default settingsAsantéBridge 1012 Local Management These functions, use the following flow chart AsantéBridge 1012 Local ManagementBridge Diagnostics Bridge DiagnosticsLocal Management Local Management Main MenuLocal Management Menu System General Help Menu Local Management Help WindowConfiguration Menu System Accessing the Configuration Menu systemConfiguration Menu System Reset System item is a command. Selecting this item System Information MenuPassword Menu Password MenuBridge Snmp agent menu has the following four submenus Snmp AgentParameters Menu System TCP/IP Parameters Menu TCP/IP Parameters MenuSoftware Update Menu Software Update MenuAbout the Software Update function Configuration Menu System 10 System Update Status Window Menu without taking any actionConfiguration Menu System Snmp Trap Receiver Table 11 Snmp Trap Receiver TableSnmp Community Name Table 12 Snmp Community Name TableThis table allows you to control access to Snmp MIB objects Out-of-Band Parameters Menu 13 Out-of-Band Parameters MenuEnter control-z to return to the Configuration Menu Bridge Parameters Menu System 14 Bridge Parameters MenuSpanning Tree Bridge Parameters Menu 15 Spanning Tree Bridge Parameters MenuActivity.To update the window, enter control-r Spanning Tree Port Setting Menu 16 Spanning Tree Port Setting MenuBridge Forwarding Table About ForwardingExit returns you to the Bridge Parameters Menu Alphabetic portion of the field defines the type of entry About dynamic and static table entriesAsantéBridge 1012 Local Management Using the Edit Function 18 Editing the Forwarding TableUsing the Search Function 19 Searching for an AddressBridge Filtering Table About the Filtering Table20 Bridge Filtering Table Configuration Menu System Resetting the Bridge 21 Resetting the BridgeMenu Statistics Menu System 22 Bridge StatisticsSupport for Pre 10BaseT Devices Appendix a Support for Pre 10BaseT Devices Technical Specifications Appendix B Technical Specifications B-3 B-4 Pinouts and Cable Specifications Appendix C Pinouts and Cable Specifications RJ-45 to RJ-21 Pinouts Amphenol to Modular JackC-3 RJ-45 Modular Jack to Wall Jack Pinouts RJ-45 to RJ-45 Crossover CableAUI DB-15 Pinouts Table C-1 AUI PinoutsC-6 AsantéBridge 1012 Index LED Numerics Manual P/N