Asante Technologies 1012 manual Appendix a Support for Pre 10BaseT Devices

Page 96

Appendix A — Support for Pre 10BaseT Devices

	This appendix provides guidelines for integrating non-10BaseT
	compatible devices for your Asanté 10BaseT Local Area Network.
	For a device that has an Ethernet card with an AUI port, simply
	obtain a TP-MAU (Media Attachment Unit) such as the Asanté 10T
	MAU.A TP-MAU is an external device which allows you to connect
	a 10BaseT RJ-45 connector to your AUI (DB-15) port.
	For a device with an adapter card that supports an earlier version
	of 10BaseT, you should disable the Link Integrity test for the port
	connected to that device. First, check with the vendor to make
	sure disabling the Link Integrity makes the card compatible with
	the AsantéHub 1012.Then do the following steps:
1	Determine which port number the workstation is wired to
1	on the AsantéHub.
2	From the AsantéView Port Control window, disable link
2	integrity testing on that port. (For this procedure, see the

AsantéView manual for your version of AsantéView.)

You should know the following:

❏AsantéView does not gather statistics from ports with Link Integrity disabled.

❏The Link/Receive LED for the disabled port(s) is always on (green).

❖Note: Link Integrity can be disabled for the uplink in hardware; see Chapter 1,“Quick Start.” ❖

Page A-2

Image 96

Contents AsantéBridge Users’ Guide Trademarks Tell Us What You Think Page Table of Contents Configuring a Redundant Link Setting Up Out-of-Band LinksConnecting a VT100 Terminal Default Settings AsantéBridge 1012 Local ManagementList of Figures Figure C-4 Crossover RJ-45 Cable page C-4 Introduction About This ManualIntroduction Intended Audience Conventions Used In This Manual Intended AudienceTell Us What You Think Technical SupportQuick Start Before You StartQuick Start Introducing AsantéBridge Introducing the AsantéBridgeBridging Between Two Segments AsantéBridge Features SnmpQuick View AsantéBridgeFront Panel Quick View RJ45 Port Connectors Bridge External Port Status LEDBridge Spanning Tree Status LEDs Bridge Hub Port Status LEDsRJ21 Port Connector AsantéBridge 1012 Rear Panel3in1 Port Through/End DIP Switch Bridge External Port AUIBridge External Port Link/Receive LED Bridge External Port Collision LEDPC/Terminal DIP Switch AC Power ConnectorOn/Off Switch FanInterpreting LEDs FlashingInstalling AsantéBridge 1012 Preparing for the InstallationInstalling the AsantéBridge Basic Installation Procedures ToolsUnpacking the AsantéBridge Positioning the AsantéBridge Asante´HubRack-mounting the AsantéBridge Page Connecting Two Segments to the AsantéBridge Dividing the Network into SegmentsShown below About Spanning TreesConnecting Devices to the AsantéBridge Using the front panel RJ45 portsWhat You Need Using the rear panel RJ21 connector Conﬁguration OptionsQuick Start Connecting to the Network Connecting to the Network Before You StartAbout Bridging About BridgingSimple Transparent Bridge Bridging between segmentsAbout Bridging Spanning Tree Like thisRedundant bridging Using the 3in1 Port Connecting to the BNC PortUsing the 3in1 Port Interconnecting Hubs on Thin Ethernet BackboneConnecting to the AUI Port Interconnecting Using Foirl Fiber Optic Inter-Repeater LinkInterconnecting to Thick Ethernet Backbone Connecting to the RJ45 in and Out Ports Connecting an In-Band Daisychaining Conﬁguring a Redundant Link Checking the Link10BaseT Conﬁguring a Redundant Link An Example ConﬁgurationIf the Main Hub Goes Down If a Link Goes Down to the Main HubSetting Up Out-of-Band Links Setting Up Out-of-Band LinksInterconnecting Hubs 10 Connecting the Asanté Management Station for Out-of-Band Recommended Method Distance RestrictionsConﬁguring Hub DIP Switches PC/Terminal SwitchThrough/End Switch Connecting a VT100 Terminal Connecting a VT100 TerminalDefault Settings Lists the factory default settingsAsantéBridge 1012 Local Management These functions, use the following ﬂow chart AsantéBridge 1012 Local ManagementBridge Diagnostics Bridge DiagnosticsLocal Management Local Management Main MenuLocal Management Menu System General Help Menu Local Management Help WindowAccessing the Conﬁguration Menu system Conﬁguration Menu SystemConﬁguration Menu System Reset System item is a command. Selecting this item System Information MenuPassword Menu Password MenuSnmp Agent Parameters Menu SystemBridge Snmp agent menu has the following four submenus TCP/IP Parameters Menu TCP/IP Parameters MenuSoftware Update Menu Software Update MenuAbout the Software Update function Conﬁguration Menu System 10 System Update Status Window Menu without taking any actionConﬁguration Menu System Snmp Trap Receiver Table 11 Snmp Trap Receiver TableSnmp Community Name Table 12 Snmp Community Name TableThis table allows you to control access to Snmp MIB objects Out-of-Band Parameters Menu 13 Out-of-Band Parameters MenuEnter control-z to return to the Conﬁguration Menu Bridge Parameters Menu System 14 Bridge Parameters MenuSpanning Tree Bridge Parameters Menu 15 Spanning Tree Bridge Parameters MenuActivity.To update the window, enter control-r Spanning Tree Port Setting Menu 16 Spanning Tree Port Setting MenuBridge Forwarding Table About ForwardingExit returns you to the Bridge Parameters Menu Alphabetic portion of the ﬁeld deﬁnes the type of entry About dynamic and static table entriesAsantéBridge 1012 Local Management Using the Edit Function 18 Editing the Forwarding TableUsing the Search Function 19 Searching for an AddressBridge Filtering Table About the Filtering Table20 Bridge Filtering Table Conﬁguration Menu System Resetting the Bridge 21 Resetting the BridgeMenu Statistics Menu System 22 Bridge StatisticsSupport for Pre 10BaseT Devices Appendix a Support for Pre 10BaseT Devices Technical Speciﬁcations Appendix B Technical Speciﬁcations B-3 B-4 Pinouts and Cable Speciﬁcations Appendix C Pinouts and Cable Speciﬁcations RJ-45 to RJ-21 Pinouts Amphenol to Modular JackC-3 RJ-45 Modular Jack to Wall Jack Pinouts RJ-45 to RJ-45 Crossover CableAUI DB-15 Pinouts Table C-1 AUI PinoutsC-6 AsantéBridge 1012 Index LED Numerics Manual P/N