Asante Technologies 1012 Conﬁguring Hub DIP Switches, PC/Terminal Switch, Through/End Switch

Page 54

Chapter 2 — Connecting to the Network

Conﬁguring Hub DIP Switches

There are two DIP switches located to the right of the AMS Link ports on the rear panel of the AsantéBridge 1012.These two switches are set up according to how the AsantéBridge is posi- tioned in the out-of-band daisychain and how you are connecting your Asanté Management Station.

Follow these simple rules to set the switches:

Through/End Switch

PC/Terminal Switch

Set UP if both AMS Link ports are in use.

Set DOWN if only one AMS port is in use

1

2

Set UP if you are connecting your

Asanté Management Station to the RS232 port and running AsantéView Out-of-Band

Set DOWN if you are connecting your Asanté Management Station to one of the AMS Link ports

Figure 2-12 Switch Settings Key

PC/Terminal Switch

❏If the Asanté Management Station is connected to the Bridge/Hub RS232 port, either directly or via a modem, and you are running AsantéView Out-of-Band, set this switch UP.

❏If you connect your station to one of the AMS Link ports and are running AsantéView Out-of-Band, set this switch

DOWN.

Through/End Switch

❏If both AMS Link ports are in use, set the switch UP.

❏If only one AMS Link port is in use, set the switch

DOWN.

Page 2-20

Image 54

Contents AsantéBridge Users’ Guide Trademarks Tell Us What You Think Page Table of Contents Connecting a VT100 Terminal Default Settings Configuring a Redundant LinkSetting Up Out-of-Band Links AsantéBridge 1012 Local ManagementList of Figures Figure C-4 Crossover RJ-45 Cable page C-4 Introduction About This ManualIntroduction Intended Audience Conventions Used In This Manual Intended AudienceTell Us What You Think Technical SupportQuick Start Before You StartQuick Start Introducing AsantéBridge Introducing the AsantéBridgeBridging Between Two Segments AsantéBridge Features SnmpQuick View AsantéBridgeFront Panel Quick View Bridge Spanning Tree Status LEDs RJ45 Port ConnectorsBridge External Port Status LED Bridge Hub Port Status LEDsRJ21 Port Connector AsantéBridge 1012 Rear Panel3in1 Port Bridge External Port Link/Receive LED Through/End DIP SwitchBridge External Port AUI Bridge External Port Collision LEDOn/Off Switch PC/Terminal DIP SwitchAC Power Connector FanInterpreting LEDs FlashingInstalling AsantéBridge 1012 Preparing for the InstallationInstalling the AsantéBridge Basic Installation Procedures ToolsUnpacking the AsantéBridge Positioning the AsantéBridge Asante´HubRack-mounting the AsantéBridge Page Connecting Two Segments to the AsantéBridge Dividing the Network into SegmentsShown below About Spanning TreesConnecting Devices to the AsantéBridge Using the front panel RJ45 portsWhat You Need Using the rear panel RJ21 connector Conﬁguration OptionsQuick Start Connecting to the Network Connecting to the Network Before You StartAbout Bridging About BridgingSimple Transparent Bridge Bridging between segmentsAbout Bridging Spanning Tree Like thisRedundant bridging Using the 3in1 Port Connecting to the BNC PortUsing the 3in1 Port Interconnecting Hubs on Thin Ethernet BackboneConnecting to the AUI Port Interconnecting Using Foirl Fiber Optic Inter-Repeater LinkInterconnecting to Thick Ethernet Backbone Connecting to the RJ45 in and Out Ports Connecting an In-Band Daisychaining Conﬁguring a Redundant Link Checking the Link10BaseT Conﬁguring a Redundant Link An Example ConﬁgurationIf the Main Hub Goes Down If a Link Goes Down to the Main HubSetting Up Out-of-Band Links Setting Up Out-of-Band LinksInterconnecting Hubs 10 Connecting the Asanté Management Station for Out-of-Band Recommended Method Distance RestrictionsConﬁguring Hub DIP Switches PC/Terminal SwitchThrough/End Switch Connecting a VT100 Terminal Connecting a VT100 TerminalDefault Settings Lists the factory default settingsAsantéBridge 1012 Local Management These functions, use the following ﬂow chart AsantéBridge 1012 Local ManagementBridge Diagnostics Bridge DiagnosticsLocal Management Local Management Main MenuLocal Management Menu System General Help Menu Local Management Help WindowAccessing the Conﬁguration Menu system Conﬁguration Menu SystemConﬁguration Menu System Reset System item is a command. Selecting this item System Information MenuPassword Menu Password MenuSnmp Agent Parameters Menu SystemBridge Snmp agent menu has the following four submenus TCP/IP Parameters Menu TCP/IP Parameters MenuSoftware Update Menu Software Update MenuAbout the Software Update function Conﬁguration Menu System 10 System Update Status Window Menu without taking any actionConﬁguration Menu System Snmp Trap Receiver Table 11 Snmp Trap Receiver TableSnmp Community Name Table 12 Snmp Community Name TableThis table allows you to control access to Snmp MIB objects Out-of-Band Parameters Menu 13 Out-of-Band Parameters MenuEnter control-z to return to the Conﬁguration Menu Bridge Parameters Menu System 14 Bridge Parameters MenuSpanning Tree Bridge Parameters Menu 15 Spanning Tree Bridge Parameters MenuActivity.To update the window, enter control-r Spanning Tree Port Setting Menu 16 Spanning Tree Port Setting MenuBridge Forwarding Table About ForwardingExit returns you to the Bridge Parameters Menu Alphabetic portion of the ﬁeld deﬁnes the type of entry About dynamic and static table entriesAsantéBridge 1012 Local Management Using the Edit Function 18 Editing the Forwarding TableUsing the Search Function 19 Searching for an AddressBridge Filtering Table About the Filtering Table20 Bridge Filtering Table Conﬁguration Menu System Resetting the Bridge 21 Resetting the BridgeMenu Statistics Menu System 22 Bridge StatisticsSupport for Pre 10BaseT Devices Appendix a Support for Pre 10BaseT Devices Technical Speciﬁcations Appendix B Technical Speciﬁcations B-3 B-4 Pinouts and Cable Speciﬁcations Appendix C Pinouts and Cable Speciﬁcations RJ-45 to RJ-21 Pinouts Amphenol to Modular JackC-3 RJ-45 Modular Jack to Wall Jack Pinouts RJ-45 to RJ-45 Crossover CableAUI DB-15 Pinouts Table C-1 AUI PinoutsC-6 AsantéBridge 1012 Index LED Numerics Manual P/N