NETGEAR WG302 manual Placement and Range Guidelines

Page 3

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice

NETGEAR ProSafe Wireless Access Point

Tested to Comply with FCC Standards

FOR HOME OR OFFICE USE

FCC ID: PY3WG302

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.This device may not cause harmful interference.

2.This device must accept any interference received, including interference that may cause undesired operation.

Placement and Range Guidelines

Indoors, computers can connect over 802.11 wireless networks at a maximum range of 500 feet (152.4 m) for 802.11b devices. However, the operating distance or range of your wireless connection can vary significantly, based on the physical placement of the wireless access point.

For best results, identify a location for your wireless access point according to these guidelines:

Away from potential sources of interference, such as PCs, large metal surfaces, microwaves, and 2.4 GHz cordless phones.

In an elevated location such as a high shelf that is near the center of the wireless coverage area for all mobile devices.

Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the wireless access point.

To meet FCC and other national safety guidelines for RF exposure, the antennas for this device must be installed to ensure a minimum separation distance of 20cm (7.9 in.) from persons. Further, the antennas shall not be colocated with other transmitting structures.

3

September 2004

Image 3
Contents September Technical Support Placement and Range Guidelines Declaration of Conformity Industry Canada Compliance Statement September Contents Chapter Management Appendix a Specifications Contents Audience, Versions, Conventions Chapter About This ManualHtml version of this manual How to Use this ManualHow to Print this Manual About This Manual Chapter Introduction Supported Standards and Conventions Key FeaturesAutoCell-The Self-Organizing Wireless Network 802.11g Standards-based Wireless Networking Autosensing Ethernet Connections with Auto UplinkCompatible and Related Netgear Products What’s In the Box? System RequirementsHardware Description Following table explains the LED indicatorsLED Description This socket connects to the WG302 12V 1.2A power adapter WG302 provides two detachable antennaMale DB-9 serial port for serial DTE connections Introduction Observing Placement and Range Guidelines Chapter Basic Installation and ConfigurationCabling Requirements Feature Factory Default Settings Default Factory SettingsLUHOHVVDWD 6HFXULW\2SWLRQV Understanding WG302 Wireless Security OptionsSET UP the WG302 Access Point Installing the WG302 Access PointLogin window Login result WG302 home Web browser will then display the WG302 settingsBasic Settings menu Configure the settings appropriate for your networkDeploy the WG302 Access Point Verify Wireless Connectivity How to Log In to the WG302 Using Its Default IP Address Understanding Basic Wireless Settings Basic Installation and Configuration Understanding WEP/WPA Security Options Wireless Security Settings Field Description Security Encryption Field Description WPA-PSK Wi-Fi Key Before You Change the Ssid and WEP SettingsHow to Set Up and Test Basic Wireless Connectivity Select the Turn Access Control On check box How to Restrict Wireless Access by MAC AddressHow to Configure WEP To configure WEP data encryption, follow these stepsClick Apply to save your settings How to Configure WPA-PSK How to Configure WPA10 Wireless Settings menu Using the Basic IP Settings OptionsAccess Point Name NetBIOS Time Zone Select the time zone location for your settingChapter Management Using the Secure Telnet InterfaceHow to Use the CLI via the Console Port These settings appear below the connector on the back panelPress the return key, and the screen below should appear CLI CommandsSyslog and Activity Log information Using Syslog and Activity Log InformationThis screen shows the following parameters Viewing General, Log, Station, and Statistical InformationField Description StatisticsWireless Access Point Status screen Statistics Fields Viewing a List of Attached Devices Upgrading the Wireless Access Point SoftwareConfiguration File Management Settings Backup menu Saving and Retrieving the ConfigurationRestoring the WG302 to the Factory Default Settings Using the Reset Button to Restore Factory Default SettingsChanging the Administrator Password Set Password menu Management Understanding Advanced IP Settings for Wireless Clients Chapter Advanced ConfigurationAutoCell RF Management Understanding Advanced Wireless SettingsAutoCell RF management is enabled by default ConfigurationAdditional AutoCell View Management Options Table below describes the advanced wireless parameters Configuring Wireless LAN ParametersAdvanced Wireless Settings Access Point Mode settings Enabling Wireless Bridging and RepeatingPoint-to-Point Bridge How to Configure a WG302 as a Point-to-Point BridgeConfigure the Operating Mode WG302 AP1 on LAN How to Configure MultiHow to Configure Wireless Repeating Advanced Configuration No lights are lit on the access point Chapter TroubleshootingLAN light is not lit Wireless LAN activity light does not light upWhen I enter a URL or IP address I get a timeout error Cannot connect to the WG302 to configure itUsing the Reset Button to Restore Factory Default Settings Specifications for the WG302 Appendix a SpecificationsSpecifications This chapter provides an overview of Wireless networking Appendix B Wireless Networking BasicsWireless Networking Overview Infrastructure ModeAuthentication and WEP Data Encryption Ad Hoc Mode Peer-to-Peer WorkgroupNetwork Name Extended Service Set Identification Essid Open System Authentication Authentication$XWKHQWLFDWLRQ6WHSV Shared Key AuthenticationSends Iteback TOO!0 Overview of WEP ParametersKey Size WEP Configuration Options Wireless ChannelsWPA Wireless Security How Does WPA Compare to WEP? How Does WPA Compare to Ieee 802.11i? What are the Key Features of WPA Security?Wireless Networking Basics Figure B-3 WPA Overview Figure B-4 802.1x Authentication Sequence Access point replies with an EAP-request identity messageWPA Data Encryption Key Management Temporal Key Integrity Protocol Tkip Product Support for WPA Is WPA Perfect?Open system, then 802.1x supplicant EAP or preshared key Open system, then 802.1x EAP with Radius or preshared keyChanges to Wireless Client Programs Command Sets Appendix C Command Line ReferenceCommand Line Reference Command Line Reference Command Line Reference Glossary Dhcp DSL Internet service provider Radius TLS Wins Glossary Numerics IndexWEP B-3
Related manuals
Manual 34 pages 38.47 Kb