NETGEAR WG302 manual Industry Canada Compliance Statement

Page 5

•Reorient or locate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Warning for North America, and Australia

Warning! To meet FCC and other national safety guidelines for RF exposure, the antennas for this device (see below) must be installed to ensure a minimum separation distance of 20cm (7.9 in.) from persons. Further, the antennas shall not be colocated with other antenna or radio transmitter.

Antenna Statement for North America and Australia

In addition to its own 2 antennas, the WG302 device has been approved for use with the following detachable antennas and antenna cables:

Approved	Antenna Gain and	Approved Antenna	Antenna Cable	Maximum
Antennas	type	Cable	Length	Transmitted Power
NETGEAR	18 dBi, directional	NETGEAR	1.5 m to 30 m	19 dBm + 18 dBi ant.
ANT24D18	outdoor/indoor	ACC-10314-01 thru 05
NETGEAR	9 dBi, omnidirectional	NETGEAR	1.5 m to 30 m	19 dBm + 9 dBi ant.
ANT2409	outdoor/indoor	ACC-10314-01 thru 05
NETGEAR	5 dBi, ceiling/wall	NETGEAR	1.5 m to 30 m	19 dBm + 5 dBi ant.
ANT24O5	indoor	ACC-10314-01 thru 05

* WG302 maximum radiated power in North America and Australia: 20 dBm – cable loss + antenna gain

Please go to www.netgear.com/go/wg302_fcc for an updated list of wireless accessories approved to be used with the WG302 in North America and Australia.

Industry Canada Compliance Statement

This Class B Digital apparatus meets all the requirements of the Canadian Interference Causing Equipment Regulations ICES 003.

Cet appareil numerique de classe B respecte les exigences du reglement du Canada sur le materiel brouilleur NMB-003.

The device is certified to the requirements of RSS-210 for 2.4 GHz spread spectrum devices. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. For further information, contact your local Industry Canada office.

5

September 2004

Image 5

Contents September Technical Support Placement and Range Guidelines Declaration of Conformity Industry Canada Compliance Statement September Contents Chapter Management Appendix a Specifications Contents Audience, Versions, Conventions Chapter About This ManualHtml version of this manual How to Use this ManualHow to Print this Manual About This Manual Chapter Introduction Supported Standards and Conventions Key FeaturesAutoCell-The Self-Organizing Wireless Network Compatible and Related Netgear Products 802.11g Standards-based Wireless NetworkingAutosensing Ethernet Connections with Auto Uplink What’s In the Box? System RequirementsHardware Description Following table explains the LED indicatorsLED Description Male DB-9 serial port for serial DTE connections This socket connects to the WG302 12V 1.2A power adapterWG302 provides two detachable antenna Introduction Observing Placement and Range Guidelines Chapter Basic Installation and ConfigurationCabling Requirements Feature Factory Default Settings Default Factory SettingsLUHOHVVDWD 6HFXULW\2SWLRQV Understanding WG302 Wireless Security OptionsSET UP the WG302 Access Point Installing the WG302 Access PointLogin window Login result WG302 home Web browser will then display the WG302 settingsBasic Settings menu Configure the settings appropriate for your networkDeploy the WG302 Access Point Verify Wireless Connectivity How to Log In to the WG302 Using Its Default IP Address Understanding Basic Wireless Settings Basic Installation and Configuration Understanding WEP/WPA Security Options Wireless Security Settings Field Description Security Encryption Field Description WPA-PSK Wi-Fi Key Before You Change the Ssid and WEP SettingsHow to Set Up and Test Basic Wireless Connectivity Select the Turn Access Control On check box How to Restrict Wireless Access by MAC AddressClick Apply to save your settings How to Configure WEPTo configure WEP data encryption, follow these steps How to Configure WPA-PSK How to Configure WPA10 Wireless Settings menu Using the Basic IP Settings OptionsAccess Point Name NetBIOS Time Zone Select the time zone location for your settingHow to Use the CLI via the Console Port Using the Secure Telnet InterfaceThese settings appear below the connector on the back panel Chapter ManagementPress the return key, and the screen below should appear CLI CommandsSyslog and Activity Log information Using Syslog and Activity Log InformationThis screen shows the following parameters Viewing General, Log, Station, and Statistical InformationField Description StatisticsWireless Access Point Status screen Statistics Fields Viewing a List of Attached Devices Upgrading the Wireless Access Point SoftwareConfiguration File Management Settings Backup menu Saving and Retrieving the ConfigurationChanging the Administrator Password Restoring the WG302 to the Factory Default SettingsUsing the Reset Button to Restore Factory Default Settings Set Password menu Management Understanding Advanced IP Settings for Wireless Clients Chapter Advanced ConfigurationAutoCell RF Management Understanding Advanced Wireless SettingsAutoCell RF management is enabled by default ConfigurationAdditional AutoCell View Management Options Table below describes the advanced wireless parameters Configuring Wireless LAN ParametersAdvanced Wireless Settings Access Point Mode settings Enabling Wireless Bridging and RepeatingPoint-to-Point Bridge How to Configure a WG302 as a Point-to-Point BridgeConfigure the Operating Mode WG302 AP1 on LAN How to Configure MultiHow to Configure Wireless Repeating Advanced Configuration No lights are lit on the access point Chapter TroubleshootingLAN light is not lit Wireless LAN activity light does not light upWhen I enter a URL or IP address I get a timeout error Cannot connect to the WG302 to configure itUsing the Reset Button to Restore Factory Default Settings Specifications for the WG302 Appendix a SpecificationsSpecifications Wireless Networking Overview Appendix B Wireless Networking BasicsInfrastructure Mode This chapter provides an overview of Wireless networkingNetwork Name Extended Service Set Identification Essid Authentication and WEP Data EncryptionAd Hoc Mode Peer-to-Peer Workgroup Open System Authentication Authentication$XWKHQWLFDWLRQ6WHSV Shared Key AuthenticationSends Iteback TOO!0 Overview of WEP ParametersKey Size WEP Configuration Options Wireless ChannelsWPA Wireless Security How Does WPA Compare to WEP? How Does WPA Compare to Ieee 802.11i? What are the Key Features of WPA Security?Wireless Networking Basics Figure B-3 WPA Overview Figure B-4 802.1x Authentication Sequence Access point replies with an EAP-request identity messageWPA Data Encryption Key Management Temporal Key Integrity Protocol Tkip Product Support for WPA Is WPA Perfect?Open system, then 802.1x supplicant EAP or preshared key Open system, then 802.1x EAP with Radius or preshared keyChanges to Wireless Client Programs Command Sets Appendix C Command Line ReferenceCommand Line Reference Command Line Reference Command Line Reference Glossary Dhcp DSL Internet service provider Radius TLS Wins Glossary Numerics IndexWEP B-3

Related manuals

Manual 34 pages 38.47 Kb