NETGEAR WG302 manual Glossary

Page 99

Glossary

Use the list below to find definitions for technical terms used in this manual.

10BASE-T

IEEE 802.3 specification for 10 Mbps Ethernet over twisted pair wiring.

100BASE-Tx

IEEE 802.3 specification for 100 Mbps Ethernet over twisted pair wiring.

802.1x

802.1x defines port-based, network access control used to provide authenticated network access and automated data encryption key management.

The IEEE 802.1x draft standard offers an effective framework for authenticating and controlling user traffic to a protected network, as well as dynamically varying encryption keys. 802.1x uses a protocol called EAP (Extensible Authentication Protocol) and supports multiple authentication methods, such as token cards, Kerberos, one-time passwords, certificates, and public key authentication. For details on EAP specifically, refer to IETF's RFC 2284.

802.11b

IEEE specification for wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.5GHz.

802.11g

A soon to be ratified IEEE specification for wireless networking at 54 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.5GHz. 802.11g is backwards compatible with 802.11b.

ADSL

Short for asymmetric digital subscriber line, a technology that allows data to be sent over existing copper telephone lines at data rates of from 1.5 to 9 Mbps when receiving data (known as the downstream rate) and from 16 to 640 Kbps when sending data (known as the upstream rate).

ADSL requires a special ADSL modem. ADSL is growing in popularity as more areas around the world gain access.

ARP

Address Resolution Protocol, a TCP/IP protocol used to convert an IP address into a physical address (called a DLC address), such as an Ethernet address.

A host wishing to obtain a physical address broadcasts an ARP request onto the TCP/IP network. The host on the network that has the IP address in the request then replies with its physical hardware address. There is

Glossary

1

September 2004

Image 99
Contents September Technical Support Placement and Range Guidelines Declaration of Conformity Industry Canada Compliance Statement September Contents Chapter Management Appendix a Specifications Contents Audience, Versions, Conventions Chapter About This ManualHtml version of this manual How to Use this ManualHow to Print this Manual About This Manual Chapter Introduction Supported Standards and Conventions Key FeaturesAutoCell-The Self-Organizing Wireless Network 802.11g Standards-based Wireless Networking Autosensing Ethernet Connections with Auto UplinkCompatible and Related Netgear Products What’s In the Box? System RequirementsHardware Description Following table explains the LED indicatorsLED Description This socket connects to the WG302 12V 1.2A power adapter WG302 provides two detachable antennaMale DB-9 serial port for serial DTE connections Introduction Observing Placement and Range Guidelines Chapter Basic Installation and ConfigurationCabling Requirements Feature Factory Default Settings Default Factory SettingsLUHOHVVDWD 6HFXULW\2SWLRQV Understanding WG302 Wireless Security OptionsSET UP the WG302 Access Point Installing the WG302 Access PointLogin window Login result WG302 home Web browser will then display the WG302 settingsBasic Settings menu Configure the settings appropriate for your networkDeploy the WG302 Access Point Verify Wireless Connectivity How to Log In to the WG302 Using Its Default IP Address Understanding Basic Wireless Settings Basic Installation and Configuration Understanding WEP/WPA Security Options Wireless Security Settings Field Description Security Encryption Field Description WPA-PSK Wi-Fi Key Before You Change the Ssid and WEP SettingsHow to Set Up and Test Basic Wireless Connectivity Select the Turn Access Control On check box How to Restrict Wireless Access by MAC AddressHow to Configure WEP To configure WEP data encryption, follow these stepsClick Apply to save your settings How to Configure WPA-PSK How to Configure WPA10 Wireless Settings menu Using the Basic IP Settings OptionsAccess Point Name NetBIOS Time Zone Select the time zone location for your settingChapter Management Using the Secure Telnet InterfaceHow to Use the CLI via the Console Port These settings appear below the connector on the back panelPress the return key, and the screen below should appear CLI CommandsSyslog and Activity Log information Using Syslog and Activity Log InformationThis screen shows the following parameters Viewing General, Log, Station, and Statistical InformationField Description StatisticsWireless Access Point Status screen Statistics Fields Viewing a List of Attached Devices Upgrading the Wireless Access Point SoftwareConfiguration File Management Settings Backup menu Saving and Retrieving the ConfigurationRestoring the WG302 to the Factory Default Settings Using the Reset Button to Restore Factory Default SettingsChanging the Administrator Password Set Password menu Management Understanding Advanced IP Settings for Wireless Clients Chapter Advanced ConfigurationAutoCell RF Management Understanding Advanced Wireless SettingsAutoCell RF management is enabled by default ConfigurationAdditional AutoCell View Management Options Table below describes the advanced wireless parameters Configuring Wireless LAN ParametersAdvanced Wireless Settings Access Point Mode settings Enabling Wireless Bridging and RepeatingPoint-to-Point Bridge How to Configure a WG302 as a Point-to-Point BridgeConfigure the Operating Mode WG302 AP1 on LAN How to Configure MultiHow to Configure Wireless Repeating Advanced Configuration No lights are lit on the access point Chapter TroubleshootingLAN light is not lit Wireless LAN activity light does not light upWhen I enter a URL or IP address I get a timeout error Cannot connect to the WG302 to configure itUsing the Reset Button to Restore Factory Default Settings Specifications for the WG302 Appendix a SpecificationsSpecifications This chapter provides an overview of Wireless networking Appendix B Wireless Networking BasicsWireless Networking Overview Infrastructure ModeAuthentication and WEP Data Encryption Ad Hoc Mode Peer-to-Peer WorkgroupNetwork Name Extended Service Set Identification Essid Open System Authentication Authentication$XWKHQWLFDWLRQ6WHSV Shared Key AuthenticationSends Iteback TOO!0 Overview of WEP ParametersKey Size WEP Configuration Options Wireless ChannelsWPA Wireless Security How Does WPA Compare to WEP? How Does WPA Compare to Ieee 802.11i? What are the Key Features of WPA Security?Wireless Networking Basics Figure B-3 WPA Overview Figure B-4 802.1x Authentication Sequence Access point replies with an EAP-request identity messageWPA Data Encryption Key Management Temporal Key Integrity Protocol Tkip Product Support for WPA Is WPA Perfect?Open system, then 802.1x supplicant EAP or preshared key Open system, then 802.1x EAP with Radius or preshared keyChanges to Wireless Client Programs Command Sets Appendix C Command Line ReferenceCommand Line Reference Command Line Reference Command Line Reference Glossary Dhcp DSL Internet service provider Radius TLS Wins Glossary Numerics IndexWEP B-3
Related manuals
Manual 34 pages 38.47 Kb