NETGEAR N450/CG3000Dv2 user manual Support, Compliance, Trademarks

Page 2

N450 WiFi Cable Modem Router Model N450/CG3000Dv2

Support

Thank you for selecting NETGEAR products.

After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website. For product updates and web support, visit http://support.netgear.com.

Phone (US & Canada only): 1-888-NETGEAR.

Phone (Other Countries): Check the list of phone numbers at http://support.netgear.com/general/contact/default.aspx.

Compliance

For regulatory compliance information, visit http://www.netgear.com/about/regulatory.

See the regulatory compliance document before connecting the power supply.

Trademarks

NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice.

© NETGEAR, Inc. All rights reserved.

2

Image 2

Contents N450 WiFi Cable Modem Router Model N450/CG3000Dv2 Trademarks SupportCompliance Contents Appendix a Supplemental Information Connecting to the Internet Unpack Your Modem Router Hardware FeaturesEthernet cable Power adapter Modem router Front Panel WPS Back Panel  To position your modem router LabelPosition Your Modem Router Cable Your Modem Router  To cable your modem router To use WPS to connect to the WiFi network Connect Computer to the Modem Router To log in to the modem router  To find and select the WiFi networkLog In to Your Modem Router View Basic Settings  To view or configure basic settingsNotify Your Internet Service Provider Cable ISP Contact Information Configuring Your Wireless Network Set Up Your Wireless Network  To view or configure the wireless settingsConfiguring Your Wireless Network Use WPS Wireless Setup Add a Client Using the WPS Button  To add a client to your modem router using the WPS buttonConfiguring Your Wireless Network Add a Client Using a PIN  To add a client to your modem router using a PINSet Up Wi-Fi Multimedia  To set up Wi-Fi MultimediaChange the Password  To change the password Filtering Content View Denial of Service Attack Logs  To view or set up notification of attacks by emailLimit Internet Site Access  To block access to sites containing certain words To allow a keyword that was previously blocked  To block access to certain domains  To unblock a domain Allow Unrestricted Access  To allow unrestricted accessEnable or Disable Modem Router Features  To enable or disable specific firewall features  To enable or disable specific web features  To enable or disable specific NAT ALG Status features Filtering Content Maintaining Your Network View the Modem Router Status  To view the modem router status To view the modem router’s initialization procedure View the Connection StatusBack Up and Restore Your Settings  To back up the settings  To restore the backup settingsView the Event Log  To view or clear the event log Run the Diagnostic Utilities  To run a ping test To clear the results from the display Traceroute Utility  To run a traceroute test To clear the results from the display Maintaining Your Network Advanced Settings Advanced Wireless Settings  To configure advanced wireless settingsConfigure the settings described in the following table MAC FilteringAdvanced Settings  To stop blocking a computer  To remove a computer from the list  To set up IP filteringIP Filtering Advanced Settings Port Blocking  To delete a device from the IP Filter List To add a custom service  To delete a custom service from the Active Filters table Port Forwarding Advanced Settings  To configure port triggering Port TriggeringAdvanced Settings  To remove a configured port trigger from the table  To return all trigger and target ranges to zero To set up a DMZ host DMZ HostSelect the Respond to Ping on WAN Port check box LAN IP Setup To configure LAN IP settings Click the Apply button Reserve an IP Address for Dhcp Use  To reserve an IP address for DhcpLAN Switch  To configure the switch ports To disable a LAN port Configure Universal Plug and Play  To configure UPnP To enable NTP Set Networking ProtocolsEnable Network Address Translation  To access a USB device from a Windows computer Access a USB Device on the Network To disable NAT  To access a USB device from a MAC computer Select Go Connect to Server Type smb//192.168.0.5 in the Server Address field To safely remove a USB device Click the Safely Remove USB Device button Troubleshooting Basic Functions Connect to the Modem Router’s Main MenuTroubleshoot a TCP/IP Network Using a Ping Utility Troubleshoot the ISP ConnectionTest the LAN Path to Your Modem Router PingTroubleshooting Supplemental Information Factory Default Settings Factory default settingsTechnical Specifications WPA/WPA2Supplemental Information