D-Link DIR-455 manual Outbound Filter Setting, Outbound Filter Rules List

Page 50

Section 3 - Configuration

Outbound Filter

Outbound Filter enables you to control what packets are allowed to pass the router. Outbound filter applies on all outbound packets.

OUTBOUND FILTER SETTING

Outbound Filter: Select this box to Enable the filter.

Use Schedule Rule: You may select Always On or choose the number of a schedule rule that you have defined.

Copy to ID: Copies the predefined filter to the specified ID

OUTBOUND FILTER RULES LIST

ID: Identifies the filter.

Source IP : Ports: Specify the local IP address and then specify the port after the colon.

Destination IP : Ports: Specify the remote IP address and then the port after the colon.

Enable: Select this box to enable the filter.

Schedule Rule #: Specify the schedule rule number.

Previous Page: Go back to the previous filter page.

Next Page: Advance to the next filter page.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

D-Link DIR-455 User Manual

46

Image 50

Contents Page Preface TrademarksTable of Contents Troubleshooting Wireless Basics ProductPackageOverviewContents Introduction Rear Panel PowerHardware Overview LAN4 LAN3 LAN2 LAN1 WAN SIMWPS Front PanelWAN LAN1 LAN2 LAN3 LAN4 SMS WlanLEDs WANInstallation Connect to Your NetworkConnect a Telephone Wireless Installation Considerations Configuration Web-based Configuration UtilityClick Internet Connection Setup Wizard to begin Setup WizardInternet Connection Setup Wizard Manual Internet Connection Setup and skip toPage Page Page Manual Internet Connection Setup Click Manual Internet Connection Setup to beginInternet Connection Internet Connection TypeDynamic IP Dhcp PPPoE Pptp IP Address Address ModeReconnect Mode Pptp Subnet MaskL2TP IP Address L2TP Subnet MaskKeep Alive AuthenticationDialed Number Static IP GRE Settings GRE TunnelTunnels Information Mode Wireless SettingsWireless Network Settings Wireless Security Mode Network Settings Router SettingsDhcp Lease Time Dhcp Server SettingsEnable Dhcp Server Secondary Wins IP AddressVPN Settings Page Tunnel 1 IKE Encapsulation Protocol ESP, AH, or ESP+AHPage Page IKE Proposal Settings Ipsec Proposal SettingsTunnel 1 Manual Key Page Encapsulation Protocol ESP, AH, or ESP+AH Preshared Key XAuth Server ModePFS Group Remote IDIKE Proposal Settings Create Message Message ServiceSMS Inbox Inbox CancelReceiver RefreshCopy to EnableVirtual Server Virtual Servers ListApplication Rules Application RulesLocal IP Ports QoS EngineQOS Packet Filter QoS PriorityMAC Filtering Rules MAC Filtering SettingsMAC Address Filter URL Filter URL Filtering RulesOutbound Filter Rules List Outbound Filter SettingOutbound Filter Inbound Filter Rules List Intbound Filter SettingInbound Filter Snmp Set CommunityRouting Rules RIP SettingRouting Advanced Wireless Dtim Interval WMM Capable TX RatesWAN Ping Advanced NetworkUpnp Remote Management AdminAdministrator Time Zone ConfigurationTime Set the Time and DateSyslog Mail Settings System Firmware Dynamic DNS Username / E-mail Enter the Username for yourSystem Check Schedules Device Information Logs Statistics Wireless Support Wireless Security What is WEP?Configure WEP Next to Security Mode, select Enable WEP SecurityWhat is WPA? Configure WPA-PSK Configure WPA Radius Connect to a Wireless Network Using Windows VistaConfigure Wireless Security Page Using Windows XP Configure WEP Page Configure WPA-PSK Page Troubleshooting Why can’t I access the web-based configuration utility?What can I do if I forgot my password? Wireless Basics Wireless Local Area Network Wlan Wireless Personal Area Network WpanHome Small Office and Home OfficeSecurity Centralize your Router or Access PointEliminate Interference Wireless Modes Networking Basics Check your IP addressStatically Assign an IP address StepTechnical Specifications GSM Band GSM/GPRS/EDGEDimensions L x W x H