Linksys WRV200 manual Setup Advanced Routing, Dynamic Routing, Static Routing

Page 17

Chapter 5

Configuring the Wireless-G Router

Setup > Advanced Routing

Setup > Advanced Routing

The Setup > Advanced Routing screen allows you to configure the dynamic and static routing settings.

Operation Mode  Select Gateway or Router from the drop-down menu. If this Router is hosting your network’s connection to the Internet, keep the default, Gateway, which will also enable NAT. If you have a different router hosting your Internet connection, then select Router.

Dynamic Routing

With Dynamic Routing you can enable the Router to automatically adjust to physical changes in the network’s layout. The Router, using the RIP protocol, determines the network packets’ route based on the fewest number of hops between the source and the destination. The RIP protocol regularly broadcasts routing information to other routers on the network.

Dynamic Routing (RIP)  To use dynamic routing, click the Enabled radio button.

Receive RIP Versions  To use dynamic routing for reception of network data, select the protocol you want: RIPv1 or RIPv2.

Transmit RIP Versions  To use dynamic routing for transmission of network data, select the protocol you want: RIPv1 or RIPv2.

Static Routing

If the Router is connected to more than one network, you can configure static routes to direct packets to the destination network (A static route is a pre-determined pathway that a packet must travel to reach a specific host or network.) To create a static route, change the following settings:

Route Entries  Select the number of the static route from the drop-down menu. The Router supports up to 5 static route entries.

Delete This Entry  If you need to delete a route, select its number from the drop-down menu, and click Delete This Entry.

Enter Router Name  Enter the name of your Router.

LAN IP Address  The LAN IP Address is the address of the remote network or host to which you want to assign a static route. Enter the IP address of the host for which you wish to create a static route. If you are building a route to an entire network, be sure that the network portion of the IP address is set to 0. For example, the Router’s standard IP address is 192.168.1.1. Based on this address, the address of the routed network is 192.168.1, with the last digit determining the Router’s place on the network. Therefore you would enter the IP address 192.168.1.0 if you wanted to route to the Router’s entire network, rather than just to the Router.

Subnet Mask  The Subnet Mask (also known as the Network Mask) determines which portion of an IP address is the network portion, and which portion is the host portion. Take, for example, a network in which the Subnet Mask is 255.255.255.0.This determines (by using the values

255)that the first three numbers of a network IP address identify this particular network, while the last digit (from 1 to 254) identifies the specific host.

Gateway  Enter the IP address of the gateway device that allows for contact between the Router and the remote network or host.

Interface  Select LAN & Wireless or Internet, depending on the location of the static route’s final destination.

Show Routing Table  Click the Show Routing Table button to open a screen displaying how packets are routed through your local network. For each route, the Destination LAN IP address, Subnet Mask, Gateway, and Interface are displayed. Click Refresh to update the information. Click Close to exit this screen.

Setup > Advanced Routing

When you have finished making changes to the screen, click Save Settings to save the changes, or click Cancel Changes to undo your changes. For help information, click More.

Wireless-G VPN Router with RangeBooster

12

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Wireless-G VPN Router with RangeBooster About This Guide About This GuideTable of Contents Appendix B Wireless Security Checklist Appendix a TroubleshootingAppendix J Contact Information Appendix E Gateway-to-Gateway VPN TunnelAppendix I Regulatory Information Introduction ChapterAd-Hoc versus Infrastructure Mode Chapter Planning Your Wireless NetworkNetwork Topology Network LayoutChapter Planning Your Virtual Private Network VPN Why do I need a VPN?What is a VPN? VPN Router to VPN Router Computer using the Linksys VPN client software to VPN RouterProduct Overview Chapter Product OverviewFront Panel Back PanelOverview Chapter Configuring the Wireless-G VPN RouterSetup How to Access the Web-based UtilitySetup Basic Settings Internet SetupPptp LAN Setup Optional Settings Required by some ISPsTime Settings Setup VlanSetup Ddns Ddns Setup MAC Address CloneStatic Routing Setup Advanced RoutingDynamic Routing Wireless Basic Wireless Settings WirelessWireless Wireless Security Wireless Network ModeWPA2 Enterprise WPA2 PersonalWPA Enterprise WPA2 Enterprise Mixed WPA2 Personal MixedWireless Network Access Wireless Wireless Network AccessAdvanced Wireless Settings Wireless Advanced Wireless SettingsWireless WDS Firewall General FirewallFirewall Port Forwarding Internet BlockFirewall DMZ Firewall Port TriggeringFirewall URL Filtering Firewall Access RestrictionVPN VPN Client Access Certificate Management VPN VPN PassthroughVPN Client List Table Remote Secure Group VPN IPSec VPNLocal Secure Group Tunnel Options Remote Secure GatewayKey Management VPN VPN Summary QoS Application-Based QoS QoSQoS Port-Based QoS Priority QueueAdministration Management AdministrationAdmin Password Local Router AccessUPnP Administration LogBackup and Restore Administration Factory Default Administration DiagnosticsAdministration Firmware Upgrade Ping TestStatus Administration RebootStatus Router InformationStatus Local Network Status WirelessStatus System Performance Local NetworkVPN Summary Status VPN ClientsSystem Performance Troubleshooting Appendix a TroubleshootingAppendix a WindowsTroubleshooting Need to set up a server behind my Router Go to the Firewall DMZ tab Click Save SettingsClick the Firewall Port Triggering tab Go to the Setup Basic Setup tabWRV200 does not support NetBIOS Broadcast over Frequently Asked QuestionsIs the Router cross-platform compatible? Wireless Security Checklist Appendix B Wireless Security ChecklistAppendix B General Network Security GuidelinesAppendix C Installing from the CD-ROMAppendix C Overview Before You BeginVersion Number of the QuickVPN Client Using the Linksys QuickVPN Software\Program Files\Linksys\QuickVPN Client\ Select VPN, then VPN Client AccessDistributing Certificates to QuickVPN Users Introduction Appendix DEnvironment Create an IPSec PolicyFilter List 2 router win Tunnel 1 win-Router Configure Individual Tunnel RulesTunnel 2 Router-win Rules Tab Your tunnel should now be established Assign New IPSec PolicyCreate a Tunnel Through the Web-Based Utility Appendix E Configuration of the WRV200Appendix E Gateway-to-Gateway VPN Tunnel Click IPSec VPNClick the Gateway to Gateway tab Configuration of the RV082Configuration of PC 1 and PC RV082 WRV200 Dynamic IP B.B.B.B with Configuration when Both Gateways Use Dynamic IP Addresses RV082 VPN Settings Appendix F Glossary Appendix FGlossary Http HyperText Transport ProtocolSmtp Simple Mail Transfer Protocol The standard e GlossaryAppendix F Appendix G Appendix G SpecificationsSpecifications Specifications Obtaining Warranty Service Warranty InformationAppendix H Exclusions and LimitationsTechnical Support Warranty InformationRegulatory Information AppendixAvis d’Industrie Canada Wireless DisclaimerDansk Danish Miljøinformation for kunder i EU Appendix Norsk Norwegian Miljøinformasjon for kunder i EU Appendix Contact Information Appendix J
Related manuals
Manual 2 pages 11.27 Kb
Top Page Image Contents