Linksys WRV200 manual Go to the Setup Basic Setup tab, Click the Firewall Port Triggering tab

Page 41

Appendix A

Troubleshooting

DSL users, it is strongly recommended to use MTU 1492. If you are having difficulties, perform the following steps:

1.To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the Router.

2.Enter the password, if asked (the default password is admin).

3.Go to the Setup -> Basic Setup tab.

4.Look for the MTU option, and select Manual. In the MTU Size field, enter 1492.

5.Click Save Settings to continue.

If your difficulties continue, change the MTU Size to different values. Try this list of values, one value at a time, in this order, until your problem is solved:

1462

1400

1362

1300

I need to use port triggering.

Port triggering looks at the outgoing port services used and will trigger the Router to open a specific port, depending on which port an Internet application uses. Follow these steps:

1.To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the Router.

2.Enter the password, if asked (the default password is admin).

3.Click the Firewall -> Port Triggering tab.

4.Enter any name you want to use for the Application Name.

5.Enter the Start and End Ports of the Triggered Range. Check with your Internet application provider for more information on which outgoing port services it is using.

6.Enter the Start and End Ports of the Forwarded Range. Check with your Internet application provider for more information on which incoming port services are required by the Internet application.

7.Check the Enabled checkbox for the entry.

When you have completed the configuration, click Save Settings.

When I enter a URL or IP address, I get a time-out error or am prompted to retry.

•Check if other PCs work. If they do, ensure that your workstation’s IP settings are correct (IP Address, Subnet Mask, Default Gateway, and DNS). Restart the computer that is having a problem.

•If the PCs are configured correctly, but still not working, check the Router. Ensure that it is connected and powered on. Connect to it and check its settings. (If you cannot connect to it, check the LAN and power connections.)

•If the Router is configured correctly, check your Internet connection (DSL/cable modem, etc.) to see if it is working correctly. You can remove the Router to verify a direct connection.

•Manually configure the TCP/IP settings with a DNS address provided by your ISP.

•Make sure that your browser is set to connect directly and that any dial-up is disabled. For Internet Explorer, clickTools,InternetOptions,andthentheConnection tab. Make sure that Internet Explorer is set to Never dial a connection. For Netscape Navigator, click Edit, Preferences, Advanced, and Proxy. Make sure that Netscape Navigator is set to Direct connection to the Internet.

I’m trying to access the Router’s Web-based Utility, but I do not see the login screen. Instead, I see a screen saying, “404 Forbidden.”

If you are using Internet Explorer, perform the following steps until you see the Web-based Utility’s login screen (Netscape Navigator will require similar steps):

1.Click File. Make sure Work Offline is NOT checked.

2.Press CTRL + F5. This is a hard refresh, which will force Internet Explorer to load new web pages, not cached ones.

3.Click Tools. Click Internet Options. Click the Security tab. Click the Default level button. Make sure the security level is Medium or lower. Then click OK.

I have a QuickVPN tunnel connected to my WRV200, but I cannot see the computers in the remote network from Windows Explorer.

QuickVPN tunneling does not support NetBIOS Broadcast. To access the computers or shared drives on the remote network, users are advised to use the IP address to identify the resource.

Ihave a Gateway-to-Gateway IPSec VPN tunnel connected between two WRV200 routers, but the users

Wireless-G VPN Router with RangeBooster

36

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Wireless-G VPN Router with RangeBooster About This Guide About This GuideTable of Contents Appendix B Wireless Security Checklist Appendix a TroubleshootingAppendix J Contact Information Appendix E Gateway-to-Gateway VPN TunnelAppendix I Regulatory Information Introduction ChapterAd-Hoc versus Infrastructure Mode Chapter Planning Your Wireless NetworkNetwork Topology Network LayoutChapter Planning Your Virtual Private Network VPN Why do I need a VPN?What is a VPN? VPN Router to VPN Router Computer using the Linksys VPN client software to VPN RouterProduct Overview Chapter Product OverviewFront Panel Back PanelOverview Chapter Configuring the Wireless-G VPN RouterSetup How to Access the Web-based UtilitySetup Basic Settings Internet SetupPptp LAN Setup Optional Settings Required by some ISPsTime Settings Setup VlanSetup Ddns Ddns Setup MAC Address CloneStatic Routing Setup Advanced RoutingDynamic Routing Wireless Basic Wireless Settings WirelessWireless Wireless Security Wireless Network ModeWPA2 Enterprise WPA2 PersonalWPA Enterprise WPA2 Enterprise Mixed WPA2 Personal MixedWireless Network Access Wireless Wireless Network AccessAdvanced Wireless Settings Wireless Advanced Wireless SettingsWireless WDS Firewall General FirewallFirewall Port Forwarding Internet BlockFirewall DMZ Firewall Port TriggeringFirewall URL Filtering Firewall Access RestrictionVPN VPN Client Access Certificate Management VPN VPN PassthroughVPN Client List Table Remote Secure Group VPN IPSec VPNLocal Secure Group Tunnel Options Remote Secure GatewayKey Management VPN VPN Summary QoS Application-Based QoS QoSQoS Port-Based QoS Priority QueueAdministration Management AdministrationAdmin Password Local Router AccessUPnP Administration LogBackup and Restore Administration Factory Default Administration DiagnosticsAdministration Firmware Upgrade Ping TestStatus Administration RebootStatus Router InformationStatus Local Network Status WirelessStatus System Performance Local NetworkVPN Summary Status VPN ClientsSystem Performance Troubleshooting Appendix a TroubleshootingAppendix a WindowsTroubleshooting Need to set up a server behind my Router Go to the Firewall DMZ tab Click Save SettingsClick the Firewall Port Triggering tab Go to the Setup Basic Setup tabWRV200 does not support NetBIOS Broadcast over Frequently Asked QuestionsIs the Router cross-platform compatible? Wireless Security Checklist Appendix B Wireless Security ChecklistAppendix B General Network Security GuidelinesAppendix C Installing from the CD-ROMAppendix C Overview Before You BeginVersion Number of the QuickVPN Client Using the Linksys QuickVPN Software\Program Files\Linksys\QuickVPN Client\ Select VPN, then VPN Client AccessDistributing Certificates to QuickVPN Users Introduction Appendix DEnvironment Create an IPSec PolicyFilter List 2 router win Tunnel 1 win-Router Configure Individual Tunnel RulesTunnel 2 Router-win Rules Tab Your tunnel should now be established Assign New IPSec PolicyCreate a Tunnel Through the Web-Based Utility Appendix E Configuration of the WRV200Appendix E Gateway-to-Gateway VPN Tunnel Click IPSec VPNClick the Gateway to Gateway tab Configuration of the RV082Configuration of PC 1 and PC RV082 WRV200 Dynamic IP B.B.B.B with Configuration when Both Gateways Use Dynamic IP Addresses RV082 VPN Settings Appendix F Glossary Appendix FGlossary Http HyperText Transport ProtocolSmtp Simple Mail Transfer Protocol The standard e GlossaryAppendix F Appendix G Appendix G SpecificationsSpecifications Specifications Obtaining Warranty Service Warranty InformationAppendix H Exclusions and LimitationsTechnical Support Warranty InformationRegulatory Information AppendixAvis d’Industrie Canada Wireless DisclaimerDansk Danish Miljøinformation for kunder i EU Appendix Norsk Norwegian Miljøinformasjon for kunder i EU Appendix Contact Information Appendix J
Related manuals
Manual 2 pages 11.27 Kb
Top Page Image Contents