Linksys BEFW11S4 manual Using IPSec Pass Through, Using Pptp Pass Through, Using Remote Management

Page 24

Instant Wireless® Series

Using Multicast Pass Through

This feature allows for multiple transmissions to specific recipients at the same time. Select Enable to support the feature, or Disable to keep the Router from multicasting.

Using IPSec Pass Through

This feature lets you use IPSec Pass Through. To use this feature, click the Enable button next to IPSec Pass Through, and then the Apply button.

IPSec Pass Through is enabled by default. To disable IPSec Pass Through, click on Disable and then the Apply button.

Using PPTP Pass Through

Point-to-Point Tunneling Protocol is the method used to enable VPN sessions. To enable this feature, click the Enable button next to PPTP Pass Through, and click the Apply button.

PPTP Pass Through is enabled by default. To disable this feature, click on Disable next to PPTP Pass Through, and then the Apply button.

Using Remote Management

This feature allows you to manage the Router from a remote location, via the Internet. To enable this feature, click on Enable, and enter the port number you want to use when accessing the Router remotely. Click the Apply button. Remote Management must be activated before you can man- age the Router from a remote location.

To disable Remote Management, click on Disable, and click the Apply but- ton. If you wish to use this feature on the browser, enter http:\\<WAN IP Address>: port. (Enter your specific WAN IP Address in place of <WAN IP Address>, and enter the port number in place of the word port.)

Wireless Access Point Router with 4-Port Switch

Using Remote Upgrade

This feature allows you to upgrade the Router’s firmware from a remote location. To enable Remote Upgrade, click on Enable, and then click the Apply button. Remote Management must be activated before you can man- age the Router from a remote location.

Important: Upgrading may cause the Router to be reset to the factory defaults. Make a record of all set- tings before attempting the upgrade.

Using MTU (Maximum Transmission Unit)

This feature specifies the largest packet size permitted for network trans- mission. Select Enable and enter the value desired. It is recommended that you leave this value in the 1200 to 1500 range. For most DSL users, it is recommended to use the value 1492. By default, MTU is set at 1500 when disabled.

39

40

Image 24
Contents Wireless Access Point Router With 4-Port Switch Copyright & Trademarks Industry Canada Canada Table of Contents Linksys Wireless Access Point Router with 4-Port Switch FeaturesIntroduction Minimum RequirementsDhcp Dynamic Host Configuration Protocol Servers IP AddressesWhat’s an IP Address? Static IP AddressesWireless Access Point Router’s Ports PowerWireless Access Point Router’s LEDs PortsConnecting the Router WAN IndicatorsConnecting Your Hardware Together and Booting Up Before You StartInstant Wireless Series Configuring the PCs Configuring Windows 95, 98, and Millennium PCsOverview Configuring Windows 2000 PCs Configuring Windows XP PCs Configuring the Router A b l e / D i s a b l eObtain an IP Automatically Static IPAddress PPPoEUsing the Router’s Web- Based Utility PptpSetup Static IP Password StatusDhcp Log Security AOL Parental ControlsHelp FiltersSetting Up Filters Editing MAC Filter SettingUsing Multicast Pass Through Advanced Tab FiltersUsing IPSec Pass Through Using Pptp Pass ThroughUsing Remote Management Using Remote UpgradeUPnP Forwarding Advanced Tab Port Range ForwardingInstant Wireless Series Port Triggering Advanced Tab Dynamic RoutingAdvanced Tab Static Routing Advanced Tab DMZ Host Advanced Tab MAC Address CloningAdvanced Tab Wireless Appendix a Troubleshooting Common Problems and SolutionsNeed to set a static IP address on a PC For Windows NT For Windows XPWant to test my Internet connection For Windows 95, 98, and MeFor Windows XP Am not able to access the Router’s web interface Setup Need to set up a server behind my RouterCan’t get the Internet game, server, or application to work To start over, I need to set the Router to factory default Need to upgrade the firmwareFirmware upgrade failed, and/or the Diag LED is flashing My DSL service’s PPPoE is always disconnectingClick the Advanced = Filter tab Need to use port triggeringDiag LED stays lit continuously Full/Col LED keeps flickering continuouslyFrequently Asked Questions Allows Pptp packets to pass through Instant Wireless Series Appendix B How to Ping Your ISP’s E-mail and Web Addresses Step One Pinging an IP AddressStep Two Pinging for a Web Address Appendix C Configuring Wireless Security Figure C-2 Configuring Wireless Security in Windows XP Figure C-3Figure C-6 Figure C-10 Figure D-3 For Windows NT, 2000, and XPFigure D-6 Http//192.168.1.1 in the webFigure E-3 AOL Broadband via DSLAppendix F Glossary Instant Wireless Series Instant Wireless Series Instant Wireless Series 100 102 104 Appendix G Specifications EnvironmentalAppendix H Warranty Information Appendix I Contact InformationWeb site FTP site Copyright 2003 Linksys, All Rights Reserved