Linksys BEFW11S4 manual Advanced Tab DMZ Host, Advanced Tab MAC Address Cloning

Page 29
Figure 5-22

Instant Wireless® Series

Advanced Tab: DMZ Host

Important: DMZ Hosting is an Advanced Function. No changes should be made to this tab without a thorough under- standing of networking concepts.

Figure 5-21

The DMZ Hosting feature, accessed from the DMZ Host tab as shown in Figure 5-21, allows one local user to be exposed to the Internet for use of a spe- cial-purpose service such as Internet gaming and videoconferencing.

Whereas Port Range Forwarding can only forward a maximum of ten port ranges, DMZ hosting forwards all the ports at the same time to one PC.

Before using this feature, the DHCP function on the PC whose port is being exposed must be disabled and have a new static IP address assigned because its IP address may change when using the DMZ function.

To expose one PC, enter the computer’s IP address. To get the IP address of a computer, refer to Appendix D: Finding the MAC Address and IP Address for Your Ethernet Adapter.

Deactivate DMZ by entering a zero in the field.

When finished, click the Apply button to save the settings. Otherwise, click the Cancel button to undo changes made on this screen.

Wireless Access Point Router with 4-Port Switch

Advanced Tab: MAC Address Cloning

Important: MAC Address Cloning is an Advanced Function. No changes should be made to this tab without a thorough understanding of networking concepts.

From the MAC Address Cloning tab, shown in Figure 5-22, you can assign the Router a MAC address, which is a 12- digit code assigned to a unique piece of hardware for identifi- cation, like a social

security number. Some ISPs require that you register the MAC address of your

network card/adapter, which was connected to your cable or DSL modem during installation. Therefore, in order to connect the Router to your cable or DSL modem in place of the PC (network card or adapter), you must change the Router MAC to duplicate (or clone) your network card/adapter MAC. You can find your adapter's MAC address by doing the following:

If you are running Windows 95, 98 or Millennium:

Go to Start, Run, type in command, and press Enter. At the DOS prompt, type winipcfg.

If you are running Windows NT 4.0 or 2000:

Go to Start, Run, type in command, and press Enter. At the DOS prompt, type ipconfig /all.

The Physical Address with 12 digits is your adapter’s MAC address. Enter those 12 digits into the MAC Address fields, and click Apply. This “clones” your network adapter’s MAC address onto the Router, and prevents you from having to call your ISP to change the registered MAC address to the adapter’s MAC address.

49

50

Image 29
Contents Wireless Access Point Router With 4-Port Switch Copyright & Trademarks Industry Canada Canada Table of Contents Features Linksys Wireless Access Point Router with 4-Port SwitchIntroduction Minimum RequirementsIP Addresses Dhcp Dynamic Host Configuration Protocol ServersWhat’s an IP Address? Static IP AddressesPower Wireless Access Point Router’s PortsWireless Access Point Router’s LEDs PortsWAN Indicators Connecting the RouterConnecting Your Hardware Together and Booting Up Before You StartInstant Wireless Series Overview Configuring the PCsConfiguring Windows 95, 98, and Millennium PCs Configuring Windows 2000 PCs Configuring Windows XP PCs A b l e / D i s a b l e Configuring the RouterStatic IP Obtain an IP AutomaticallyAddress PPPoEPptp Using the Router’s Web- Based UtilitySetup Static IP Status PasswordDhcp Log AOL Parental Controls SecurityFilters HelpEditing MAC Filter Setting Setting Up FiltersUsing Multicast Pass Through Advanced Tab FiltersUsing Pptp Pass Through Using IPSec Pass ThroughUsing Remote Management Using Remote UpgradeAdvanced Tab Port Range Forwarding UPnP ForwardingInstant Wireless Series Advanced Tab Dynamic Routing Port TriggeringAdvanced Tab Static Routing Advanced Tab MAC Address Cloning Advanced Tab DMZ HostAdvanced Tab Wireless Need to set a static IP address on a PC Appendix a TroubleshootingCommon Problems and Solutions For Windows XP For Windows NTWant to test my Internet connection For Windows 95, 98, and MeFor Windows XP Need to set up a server behind my Router Am not able to access the Router’s web interface SetupCan’t get the Internet game, server, or application to work Need to upgrade the firmware To start over, I need to set the Router to factory defaultFirmware upgrade failed, and/or the Diag LED is flashing My DSL service’s PPPoE is always disconnectingNeed to use port triggering Click the Advanced = Filter tabDiag LED stays lit continuously Full/Col LED keeps flickering continuouslyFrequently Asked Questions Allows Pptp packets to pass through Instant Wireless Series Step Two Pinging for a Web Address Appendix B How to Ping Your ISP’s E-mail and Web AddressesStep One Pinging an IP Address Appendix C Configuring Wireless Security Figure C-2 Figure C-3 Configuring Wireless Security in Windows XPFigure C-6 Figure C-10 For Windows NT, 2000, and XP Figure D-3Http//192.168.1.1 in the web Figure D-6AOL Broadband via DSL Figure E-3Appendix F Glossary Instant Wireless Series Instant Wireless Series Instant Wireless Series 100 102 104 Environmental Appendix G SpecificationsWeb site FTP site Appendix H Warranty InformationAppendix I Contact Information Copyright 2003 Linksys, All Rights Reserved