Linksys BEFW11S4 manual Industry Canada Canada

Page 3

•Reorient or relocate the receiving antenna

•Increase the separation between the equipment or devices

•Connect the equipment to an outlet other than the receiver’s

•Consult a dealer or an experienced radio/TV technician for assistance

FCC Caution: Any changes or modifications nor expressly approved by the party respon- sible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC RF Radiation Exposure Statement

This device and its antenna(s) must operate with a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users must be provided with specific operations for satisfy- ing RF exposure compliance.

INDUSTRY CANADA (CANADA)

This Class B digital apparatus complies with Canadian IC-03.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations.

EC DECLARATION OF CONFORMITY (EUROPE)

Linksys Group declares that the Instant Wireless Series products included in the Instant Wireless Series conform to the specifications listed below, following the provisions of the EMC Directive 89/336/EEC and Low Voltage Directive 73/23/EEC:

ETS 301489-17, 301 489-1 General EMC requirements for Radio equipment. EN 609 50 Safety

ETS 300-328-2 Technical requirements for Radio equipment.

Note: This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Linksys Corporate Compliance.

Note: Combinations of power levels and antennas resulting in a radiated power level of above 100 mW are considered as not compliant with the above mentioned directive and are not allowed for use within the European community and countries that have adopted the European R&TTE directive 1999/5/EC and/or the CEPT recommendation Rec 70.03. For more details on legal combinations of power levels and antennas, contact Linksys Corporate Compliance.

•Linksys Group vakuuttaa täten että Instant Wireless Wireless Access Point Router with 4-Port Switch tyyppinen laite on direktiivin 1999/5/EY, direktiivin 89/336/EEC ja direktiivin 73/23/EEC oleellisten vaatimusten ja sitä koskevien näiden direktiivien muiden ehtojen mukainen.

•Linksys Group déclare que le routeur de point d’accès sans fil avec commutateur 4 ports est conforme aux conditions essentielles et aux dispositions relatives à la directive 1999/5/EC, la directive 89/336/EEC, et à la directive 73/23/EEC.

•Belgique B L’utilisation en extérieur est autorisé sur le canal 11 (2462 MHz), 12 (2467 MHz), et 13 (2472 MHz). Dans le cas d’une utilisation privée, à l’extérieur d’un bâti- ment, au-dessus d’un espace public, aucun enregistrement n’est nécessaire pour une distance de moins de 300m. Pour une distance supérieure à 300m un enreg- istrement auprès de l’IBPT est requise. Pour une utilisation publique à l’extérieur de bâtiments, une licence de l’IBPT est requise. Pour les enregistrements et licences, veuillez contacter l’IBPT.

•France F: Bande de fréquence restreinte: seuls les canaux 10, 11, 12, 13 (2457, 2462, 2467, et 2472 MHz respectivement) doivent être utilisés en France. Toute util- isation, qu'elle soit intérieure ou extérieure, est soumise à autorisation. Vous pouvez contacter l'Autorité de Régulation des Télécommuniations (http://www.art-telecom.fr) pour la procédure à suivre.

•France F: Restricted frequency band: only channels 10, 11, 12, 13 (2457, 2462, 2467, and 2472 MHz respectively) may be used in France. License required for every indoor and outdoor installations. Please contact ART for procedure to follow.

•Deutschland D: Anmeldung im Outdoor-Bereich notwending, aber nicht genehmi- gungspflichtig. Bitte mit Händler die Vorgehensweise abstimmen.

•Germany D: License required for outdoor installations. Check with reseller for proce- dure to follow.

•Italia I: E' necessaria la concessione ministeriale anche per l'uso interno. Verificare con i rivenditori la procedura da seguire. L'uso per installazione in esterni non e' per- messa.

•Italy I: License required for indoor use. Use with outdoor installations not allowed.

•the Netherlands NL License required for outdoor installations. Check with reseller for procedure to follow.

•Nederlands NL Licentie verplicht voor gebruik met buitenantennes. Neem contact op met verkoper voor juiste procedure.

BEFW11S4V3.2-UG-30218NC JL

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Wireless Access Point Router With 4-Port Switch Copyright & Trademarks Industry Canada Canada Table of Contents Minimum Requirements Linksys Wireless Access Point Router with 4-Port SwitchFeatures IntroductionStatic IP Addresses Dhcp Dynamic Host Configuration Protocol ServersIP Addresses What’s an IP Address?Ports Wireless Access Point Router’s PortsPower Wireless Access Point Router’s LEDsBefore You Start Connecting the RouterWAN Indicators Connecting Your Hardware Together and Booting UpInstant Wireless Series Configuring the PCs Configuring Windows 95, 98, and Millennium PCsOverview Configuring Windows 2000 PCs Configuring Windows XP PCs A b l e / D i s a b l e Configuring the RouterPPPoE Obtain an IP AutomaticallyStatic IP AddressPptp Using the Router’s Web- Based UtilitySetup Static IP Status PasswordDhcp Log AOL Parental Controls SecurityFilters HelpAdvanced Tab Filters Setting Up FiltersEditing MAC Filter Setting Using Multicast Pass ThroughUsing Remote Upgrade Using IPSec Pass ThroughUsing Pptp Pass Through Using Remote ManagementAdvanced Tab Port Range Forwarding UPnP ForwardingInstant Wireless Series Advanced Tab Dynamic Routing Port TriggeringAdvanced Tab Static Routing Advanced Tab MAC Address Cloning Advanced Tab DMZ HostAdvanced Tab Wireless Appendix a Troubleshooting Common Problems and SolutionsNeed to set a static IP address on a PC For Windows 95, 98, and Me For Windows NTFor Windows XP Want to test my Internet connectionFor Windows XP Need to set up a server behind my Router Am not able to access the Router’s web interface SetupCan’t get the Internet game, server, or application to work My DSL service’s PPPoE is always disconnecting To start over, I need to set the Router to factory defaultNeed to upgrade the firmware Firmware upgrade failed, and/or the Diag LED is flashingFull/Col LED keeps flickering continuously Click the Advanced = Filter tabNeed to use port triggering Diag LED stays lit continuouslyFrequently Asked Questions Allows Pptp packets to pass through Instant Wireless Series Appendix B How to Ping Your ISP’s E-mail and Web Addresses Step One Pinging an IP AddressStep Two Pinging for a Web Address Appendix C Configuring Wireless Security Figure C-2 Figure C-3 Configuring Wireless Security in Windows XPFigure C-6 Figure C-10 For Windows NT, 2000, and XP Figure D-3Http//192.168.1.1 in the web Figure D-6AOL Broadband via DSL Figure E-3Appendix F Glossary Instant Wireless Series Instant Wireless Series Instant Wireless Series 100 102 104 Environmental Appendix G SpecificationsAppendix H Warranty Information Appendix I Contact InformationWeb site FTP site Copyright 2003 Linksys, All Rights Reserved
Top Page Image Contents