Linksys RV0041 manual Dhcp Tab Setup, Dynamic IP, Static IP

Page 35

10/100/1000 4-Port VPN Router

DHCP Tab - Setup

Setup

The Router can be used as a DHCP (Dynamic Host Configuration Protocol) server on your network. A DHCP server assigns available IP addresses to each computer on your network automatically. If you choose to enable the DHCP server option, you must configure all of the PCs on your LAN to connect to a DHCP server. (See Appendix F: Windows Help.)

Enable DHCP Server: Check the box to enable the DHCP Server. If you already have a DHCP server on your network, leave the box blank.

Dynamic IP

Client Lease Time: This is the amount of time each network PC will have an IP Address assigned to it before it dynamically changes. The range is 5 ~ 43,200 Minutes.

Dynamic IP Range Start/End: Enter a starting IP address and ending IP address to make a range to assign dynamic IPs. The default range is 100~149.

Static IP

The Static IP section of this screen is provided in the event you want the IP Addresses of certain PCs on your network to remain static. In this event, enter the Static IP Address in the space provided, along with that PC’s MAC Address.

Click Add to list to add a route entry or click Delete Selected IP to delete the static route entry.

DNS

For faster access to DNS Servers through the DHCP Server, enter the IP Address of the DNS Servers in the spaces provided.

WINS

Windows Internet Naming Service (WINS) is a service that turns NetBIOS names to IP addresses. Enter the WINS IP Address here. If you do not know the WINS, leave it as 0.

Click the Save Settings button to save the DHCP settings or click the Cancel Changes button to undo the changes.

Chapter 5: Setting Up and Configuring the Router

Figure 5-21: DHCP Setup

27

DHCP Tab - Setup

Image 35

Contents 10/100/1000 4-Port Word definition Copyright and TrademarksTable of Contents Setting up the Router Appendix a TroubleshootingAppendix C Physical Setup of the Router Appendix D Battery Replacement10/100/1000 4-Port VPN Router Computer-to-VPN Router VPN VPN Router-to-VPN Router VPN24 System Management Tab DNS Name Lookup 54 Basic Setup Wizard Host and Domain Name IP a protocol used to send data over a network IntroductionWelcome Adapter a device that adds network functionality to your PC What’s in this Guide?Introduction What’s in this Guide? Use of IP Addresses Networking BasicsAn Introduction to LANs MAC Address Spoofing Why do I need a VPN?There are two basic ways to create a VPN connection What is a VPN?VPN Router-to-VPN Router VPN VPN Router to VPN RouterSFP Getting to Know the RouterProceed to Connecting the Router Reset Button Reset button can be used in one of two waysButton on your PC to reboot it Forwarding or a new passwordVPN Router Connecting the RouterOverview Connection Instructions Setting Up and Configuring the RouterSystem Summary Tab Setting Up and Configuring the RouterSetup Tab Port Management Tab Dhcp TabSystem Management Tab Wizard Tab Firewall TabVPN Tab Log TabSystem Information How to Access the Web-based UtilityConfiguration System Summary TabPort Statistics Network Setting StatusFirewall Setting Status Log Setting Status VPN Setting StatusWAN Connection Type LAN SettingWAN Interface Setting NetworkPptp Point-to-Point Tunneling Protocol Static IPPPPoE Point-to-Point Protocol over Ethernet most DSL users Time Setup Tab PasswordSetup Tab Time Setup Tab Forwarding Setup Tab DMZ HostPort Triggering Select the Service from the pull-down menu, shown in FigurePort Range Forwarding Setup Tab One-to-One NAT Setup Tab UPnPSetup Tab Ddns Setup Tab MAC CloneDynamic Routing Setup Tab Advanced RoutingEnter the following data to create a static route entry Static RoutingStatic IP Dhcp Tab SetupSetup Dynamic IPSystem Management Tab Snmp Dhcp Tab StatusLookup tool may be used to find the IP address System Management Tab DiagnosticDNS Name Lookup PingFirmware Download System Management Tab Factory DefaultSystem Management Tab Firmware Upgrade Firmware UpgradeSystem Management Tab Restart System Management Tab Setting BackupImport Configuration File Export Configuration FileBasic Per Port Config Port Management Tab Port Setup32 Port Management Tab Port Status Port Management Tab Port Status33 Firewall Tab General Firewall Tab General34 Firewall Tab Access Rules Firewall Tab Access RulesScheduling Add a New Access RuleServices Scheduling Firewall Tab Content FilterEditing an Access Rule Forbidden DomainsTunnel Status VPN Tab SummarySummary 37 VPN Tab Summary Detail GroupVPN StatusVPN Tab Gateway to Gateway Local Group Setup40 VPN tab Gateway to Gateway Remote Group Setup Remote Group SetupManual IPSec SetupIKE with Preshared Key automatic 10/100/1000 4-Port VPN Router 42 VPN tab Gateway to Gateway Advanced AdvancedVPN Tab Client to Gateway With Tunnel Enabled45 VPN tab Client to Gateway Remote Group Setup With Group VPN enabled 46 VPN tab Client to Gateway IPSec Setup IKE with Preshared Key automatic 47 VPN tab Client to Gateway Advanced Tunnel mode, it will also be limited as Aggressive ModeCompress Support IP Payload compression Protocol IP Comp VPN Tab VPN Pass ThroughMail Log SettingLog Tab System Log Syslog51 Log tab System Statistics Log Tab System StatisticsWizard Tab Basic Setup55 Basic Setup Wizard Selecting WAN Connection Types 57 Access Rule Wizard What is Access Rules Access Rule Setup59 Access Rule Wizard Select the Service 61 Access Rule Wizard Select the Destination Linksys Web Site Support TabLogout Tab On Line ManualNeed to set a static IP address on a PC Appendix a TroubleshootingCommon Problems and Solutions For Windows 98 and MillenniumFor Windows XP For WindowsFor Windows 98 and Millennium 10/100/1000 4-Port VPN Router Need to set up a server behind my Router Am not able to access the Router’s Web-based Utility SetupWeb server 80 to Both 192.168.1.100 FTP server 21 to Application Start and End Protocol IP Address EnableClick the DMZ Host tab Application Start and End Protocol IP Address Enabled500 to Can’t get the Internet game, server, or application to workFor Netscape 4.7 or higher To start over, I need to set the Router to factory defaultNeed to upgrade the firmware For Microsoft Internet Explorer 5.0 or higherMy DSL service’s PPPoE is always disconnecting Firmware upgrade failedNeed to use port triggering Is IPSec Passthrough supported by the Router? Frequently Asked QuestionsWhere is the Router installed on the network? Router will support up to 253 IP addressesHow can I block corrupted FTP downloads? Is the Router cross-platform compatible? What is DMZ Hosting?Router allows Pptp packets to pass through Ask your ISP to find out How many ports can be simultaneously forwarded?Which modems are compatible with the Router? How can I check whether I have static or Dhcp IP addresses?Windows 2000 or XP Instructions Windows 98 or Me InstructionsFigure B-3 MAC Address/Physical Address For the Router’s Web-based UtilityRack-Mounting the Router Appendix C Physical Setup of the RouterSetting up the Router Placement of the Router10/100/1000 4-Port VPN Router Figure C-3 Wall-Mounting the Router Wall-Mounting the RouterFigure C-4 Wall-Mounting Hardware This section instructs the user on battery replacement Appendix D Battery ReplacementReplacing a Lithium Battery Appendix E Upgrading Firmware Figure E-1 Upgrade FirmwareNetwork Neighborhood/My Network Places Appendix F Windows HelpShared Resources Appendix G Glossary 10/100/1000 4-Port VPN Router 10/100/1000 4-Port VPN Router 10/100/1000 4-Port VPN Router 10/100/100 Gigabit Ports, 1 10/100 RJ-45 Internet Port Appendix H SpecificationsStandards Ieee 802.3, 802.3u Ports SFP PortLimited Warranty Appendix I Warranty InformationFCC Statement Appendix J Regulatory InformationLinksys Appendix K Contact InformationNeed to contact Linksys? Information section in this Guide