Linksys RV0041 manual VPN Tab Client to Gateway, With Tunnel Enabled

Page 54

10/100/1000 4-Port VPN Router

VPN Tab - Client to Gateway

With Tunnel Enabled

This screen allows you to create VPN tunnels from remote PCs (with Linksys VPN Client Software) to VPN routers. You can reach this page by clicking the Client to Gateway tab or from the Mode Choose screen (figure 5-44).

Tunnel No.: This shows the number assigned to this tunnel, from 1~5, depending on how many tunnels you have already set up.

Tunnel Name: Enter the Tunnel Name, such as LA Office, Branch Site, Corporate Site, etc. This is to allow you to identify multiple tunnels, and does not have to match the name used at the other end of the tunnel.

Enable: Checking this box enables the VPN tunnel you’re creating.

Local Group Setup

The Local Group Setup section configures the local settings for the VPN tunnel you are creating. Remember, all settings for the Local Group must be exactly the same as those for the Remote Group.

Local Security Gateway Type: There are five types. They are IP Only, IP + Domain Name (FQDN) Authentication, IP + E-mail Addr. (USER FQDN) Authentication, Dynamic IP + Domain Name (FQDN) Authentication, Dynamic IP + E-mail Addr. (USER FQDN) Authentication. The type of Local Security Gateway Type must match the Remote Security Gateway Type of VPN devices in the other end of tunnel. The first three options are easier to use because the IP Addresses are static and do not change.

IP Only: If you select IP Only, only the specific IP Address set will be able to access the tunnel. The Router’s WAN IP address (set above) will automatically appear in this field.

IP + Domain Name (FQDN) Authentication: This selection affords a greater amount of security because each side of the tunnel must use the same IP Address as well as the same domain name. Only one domain name can be used for one tunnel and may not be applied to another tunnel.These settings must match the Remote Group Setup on the other end of the tunnel.

IP + E-mail Addr. (USER FQDN) Authentication: This selection affords a greater amount of security because each side of the tunnel must use the same IP Address as well as the same email. Only one email address can be used for one tunnel and may not be applied to another tunnel.These settings must match the Remote Group Setup on the other end of the tunnel.

Dynamic IP + Domain Name (FQDN) Authentication: This setting uses a dynamic IP address, which is constantly changing. In addition, the tunnel is confirmed through use of a domain name. Only one domain

Chapter 5: Setting Up and Configuring the Router

Figure 5-43: VPN tab - Client to Gateway

Figure 5-44: VPN tab - Client to Gateway

Local Group Setup

46

VPN Tab - Client to Gateway

Page 53 Page 55
Image 54
Page 53 Page 55
Contents 10/100/1000 4-Port Copyright and Trademarks Word definitionTable of Contents Appendix D Battery Replacement Appendix a TroubleshootingAppendix C Physical Setup of the Router Setting up the Router10/100/1000 4-Port VPN Router VPN Router-to-VPN Router VPN Computer-to-VPN Router VPN24 System Management Tab DNS Name Lookup 54 Basic Setup Wizard Host and Domain Name Introduction WelcomeIP a protocol used to send data over a network What’s in this Guide? Adapter a device that adds network functionality to your PCIntroduction What’s in this Guide? Networking Basics An Introduction to LANsUse of IP Addresses Why do I need a VPN? MAC Address SpoofingWhat is a VPN? There are two basic ways to create a VPN connectionVPN Router to VPN Router VPN Router-to-VPN Router VPNGetting to Know the Router SFPForwarding or a new password Reset Button Reset button can be used in one of two waysButton on your PC to reboot it Proceed to Connecting the RouterConnecting the Router OverviewVPN Router Setting Up and Configuring the Router Connection InstructionsSetting Up and Configuring the Router Setup TabSystem Summary Tab Dhcp Tab System Management TabPort Management Tab Log Tab Firewall TabVPN Tab Wizard TabSystem Summary Tab How to Access the Web-based UtilityConfiguration System InformationNetwork Setting Status Firewall Setting StatusPort Statistics VPN Setting Status Log Setting StatusNetwork LAN SettingWAN Interface Setting WAN Connection TypeStatic IP PPPoE Point-to-Point Protocol over Ethernet most DSL usersPptp Point-to-Point Tunneling Protocol Setup Tab Password Setup Tab TimeTime Setup Tab DMZ Host Setup Tab ForwardingSelect the Service from the pull-down menu, shown in Figure Port Range ForwardingPort Triggering Setup Tab UPnP Setup Tab One-to-One NATSetup Tab MAC Clone Setup Tab DdnsSetup Tab Advanced Routing Dynamic RoutingStatic Routing Enter the following data to create a static route entryDynamic IP Dhcp Tab SetupSetup Static IPDhcp Tab Status System Management Tab SnmpPing System Management Tab DiagnosticDNS Name Lookup Lookup tool may be used to find the IP addressFirmware Upgrade System Management Tab Factory DefaultSystem Management Tab Firmware Upgrade Firmware DownloadExport Configuration File System Management Tab Setting BackupImport Configuration File System Management Tab RestartPort Management Tab Port Setup Basic Per Port ConfigPort Management Tab Port Status 32 Port Management Tab Port StatusFirewall Tab General 33 Firewall Tab GeneralFirewall Tab Access Rules 34 Firewall Tab Access RulesAdd a New Access Rule ServicesScheduling Forbidden Domains Firewall Tab Content FilterEditing an Access Rule SchedulingVPN Tab Summary SummaryTunnel Status GroupVPN Status 37 VPN Tab Summary DetailLocal Group Setup VPN Tab Gateway to GatewayRemote Group Setup 40 VPN tab Gateway to Gateway Remote Group SetupIPSec Setup ManualIKE with Preshared Key automatic 10/100/1000 4-Port VPN Router Advanced 42 VPN tab Gateway to Gateway AdvancedWith Tunnel Enabled VPN Tab Client to Gateway45 VPN tab Client to Gateway Remote Group Setup With Group VPN enabled 46 VPN tab Client to Gateway IPSec Setup IKE with Preshared Key automatic Tunnel mode, it will also be limited as Aggressive Mode 47 VPN tab Client to Gateway AdvancedVPN Tab VPN Pass Through Compress Support IP Payload compression Protocol IP CompSyslog Log SettingLog Tab System Log MailLog Tab System Statistics 51 Log tab System StatisticsBasic Setup Wizard Tab55 Basic Setup Wizard Selecting WAN Connection Types Access Rule Setup 57 Access Rule Wizard What is Access Rules59 Access Rule Wizard Select the Service 61 Access Rule Wizard Select the Destination On Line Manual Support TabLogout Tab Linksys Web SiteFor Windows 98 and Millennium Appendix a TroubleshootingCommon Problems and Solutions Need to set a static IP address on a PCFor Windows For Windows XPFor Windows 98 and Millennium 10/100/1000 4-Port VPN Router Am not able to access the Router’s Web-based Utility Setup Need to set up a server behind my RouterApplication Start and End Protocol IP Address Enable Web server 80 to Both 192.168.1.100 FTP server 21 toCan’t get the Internet game, server, or application to work Application Start and End Protocol IP Address Enabled500 to Click the DMZ Host tabFor Microsoft Internet Explorer 5.0 or higher To start over, I need to set the Router to factory defaultNeed to upgrade the firmware For Netscape 4.7 or higherFirmware upgrade failed My DSL service’s PPPoE is always disconnectingNeed to use port triggering Router will support up to 253 IP addresses Frequently Asked QuestionsWhere is the Router installed on the network? Is IPSec Passthrough supported by the Router?How can I block corrupted FTP downloads? What is DMZ Hosting? Router allows Pptp packets to pass throughIs the Router cross-platform compatible? How can I check whether I have static or Dhcp IP addresses? How many ports can be simultaneously forwarded?Which modems are compatible with the Router? Ask your ISP to find outWindows 98 or Me Instructions Windows 2000 or XP InstructionsFor the Router’s Web-based Utility Figure B-3 MAC Address/Physical AddressPlacement of the Router Appendix C Physical Setup of the RouterSetting up the Router Rack-Mounting the Router10/100/1000 4-Port VPN Router Wall-Mounting the Router Figure C-3 Wall-Mounting the RouterFigure C-4 Wall-Mounting Hardware Appendix D Battery Replacement Replacing a Lithium BatteryThis section instructs the user on battery replacement Figure E-1 Upgrade Firmware Appendix E Upgrading FirmwareAppendix F Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix G Glossary 10/100/1000 4-Port VPN Router 10/100/1000 4-Port VPN Router 10/100/1000 4-Port VPN Router SFP Port Appendix H SpecificationsStandards Ieee 802.3, 802.3u Ports 10/100/100 Gigabit Ports, 1 10/100 RJ-45 Internet PortAppendix I Warranty Information Limited WarrantyAppendix J Regulatory Information FCC StatementInformation section in this Guide Appendix K Contact InformationNeed to contact Linksys? Linksys
Top Page Image Contents